FitmentSpec Logo

Wheel Swap & Fitment Interchangeability Calculator

Will factory or aftermarket wheels from another car fit your vehicle? Select your donor and recipient models to instantly calculate bolt pattern (PCD) alignment, hub-centric spigot step-down requirements, fastener thread specs, and offset variance.

🔄

Wheel Swap & Interchangeability Diagnostic Matrix

Select the vehicle donating the wheels and the target vehicle to inspect hub spigot, bolt circle, and offset clearance.

Donor Vehicle (Source Wheels)
PCD Pattern5x114.3
Center Bore64.1 mm
Fastener ThreadM12 x 1.5
OEM Offset Span+45 to +55
Target Vehicle (Receiving Car)
PCD Pattern5x114.3
Center Bore64.1 mm
Fastener ThreadM12x1.5
OEM Offset Span+38 to +50
âš ī¸ CONDITIONAL FITAcura ➔ Acura

Mountable with Hardware Adjustments. Bolt pattern matches (5x114.3), but hub-centric adapter rings (64.1mm to 64.1mm) or fastener seat verification are required.

✓Bolt Pattern (PCD) Check:
Exact Match (5x114.3)
✓Hub Center Bore Clearance:
Direct 1:1 Hub Fit (64.1mm)
â„šī¸Fastener Thread & Seat Surface:
Use Acura Spec (M12x1.5 Radius / Ball Seat (OEM Honda/Acura) - Requires 60° Conical for Aftermarket)
✓Estimated Offset Delta (ET):
6mm Further Inboard
FitmentSpec Wheel Swap Matrix â€ĸ Always torque wheel fasteners to recipient vehicle specification.

📐 The 4 Golden Rules of Wheel Interchangeability

1. Exact PCD Match Only Pitch Circle Diameter (e.g. 5x114.3 vs 5x120) must match identically. Never force a wheel onto lug studs of a different circle diameter; it will cause stud shear under braking.
2. Hub Bore & Center Rings If the donor wheel's center bore is larger than your hub (e.g. 73.1mm wheel on 60.1mm Toyota hub), use hub-centric rings to center the wheel on the hub spigot rather than relying solely on lug nuts.
3. Fastener Seating Profile Lug nut seating surfaces vary: Honda and VW OEM wheels use Ball (Radius) seats; Toyota and aftermarket wheels use Conical (60° Acorn) seats. Using the wrong seat creates loose wheels.
4. Brake Caliper Clearance Wheel diameter and spoke contour must physically clear front brake caliper overhang, particularly on performance packages (Brembo, TRD, M Sport).

Bolt Pattern Cross-Reference Directories (PCD Clusters)

Browse every vehicle sharing an identical lug pattern, grouped by center bore for direct hub-centric wheel swaps.

How to Measure PCD →
Interchangeability Engineering FAQ

Frequently Asked Wheel Swap Questions

4 Verified Q&As
Q Will wheels from one car brand fit another if the bolt pattern is identical?
Only if the center bore (hub hole) is equal to or larger than the receiving car's hub spigot. If the wheel's center bore is larger, you must use precision aluminum or polycarbonate hub-centric rings to prevent high-speed steering wheel vibrations. If the wheel's center bore is smaller, the wheel will not seat flat against the brake rotor and cannot be installed safely.
Q Can I use 'wobble bolts' (variable PCD bolts) to mount 5x114.3 wheels on a 5x112 car?
While wobble bolts exist, FitmentSpec engineers strongly advise against them for track or high-performance use. A mismatch in bolt pattern introduces non-concentric shear loads on fastener studs. Always match the exact Pitch Circle Diameter (PCD) specified by the vehicle manufacturer.
Q What is the danger of running wheels with an incorrect offset (ET)?
If the offset is too high (wheel sits too far inboard), the inner wheel rim or tire sidewall can rub against the front MacPherson strut or control arm. If the offset is too low (wheel pokes outward), the outer tire shoulder will contact the fender lip over bumps and compressions, potentially slicing tire rubber or buckling fenders.
Q Do lug nuts stay with the wheel or the receiving vehicle during a swap?
Lug nuts must ALWAYS match the vehicle's hub studs (thread pitch and diameter, e.g. M12x1.5 vs M14x1.5) AND match the wheel's seating surface (Conical 60° vs Ball Seat vs Mag flat seat). Never use OEM Honda or VW ball-seat lug nuts on aftermarket conical-seat wheels.