FitmentSpec Logo
Buyer Due Diligence Updated for 2024–2026 Models

Vehicle Pre-Purchase Inspection: Chassis, Hub & Fitment Guide

Planning to buy a new or used vehicle? Hidden wheel bearing damage, improper aftermarket wheels, bent suspension geometry, or bypassed TPMS sensors can cost thousands to rectify. Follow our engineering checklist or select your target vehicle below for instant chronic TSB fault telemetry.

Interactive Vehicle Scanner

Target Vehicle Chassis & Chronic Fault Inspector

Select the specific vehicle you are planning to purchase to instantly reveal documented TSB faults, hub bearing checks, and fitment pitfalls.

Open 2022 ILX Specs→
Acura
1st Gen DE1-DE3 (Base / Premium / Technology / A-Spec)(2013–2022)

Inspection Profile: 2022 Acura ILX

Bolt: 5x114.3Center Bore: 64.1mmLug Torque: 80 ft-lbs
✅ No critical chassis TSBs logged for this platform. Perform standard hub and ball joint checks.
Need complete tire trims, TPMS reset guide or offset simulator?
View the full technical spec page for 2022 Acura ILX.
Open Full 2022 Fitment Page →

📋 Universal 8-Point Physical Inspection Checklist

Step-by-step mechanical checks to perform before making an offer on any used or certified vehicle.

STEP 01 Alignment & Struts

Tire Tread Wear Patterns (Suspension Geometry Clues)

Examine all 4 tires across their entire tread width. Inner edge wear indicates negative camber or excessive toe-out. Scalloped or cupped tire patches indicate dead shock absorbers bouncing uncontrollably. Feathering along tread ribs points to misaligned toe.

Pro Test Action: Run your palm across the tire tread in both directions. Sharp edges indicate severe toe misalignment requiring immediate alignment.
STEP 02 Hub Assembly

Wheel Hub & Bearing Wobble Test

Raise each wheel securely off the ground. Place hands at the 12 o’clock and 6 o’clock positions and push/pull firmly. Any audible click or physical play indicates worn wheel bearings or ball joints. Rock hands at 9 and 3 o’clock to check tie rod ends.

Pro Test Action: Spin the wheel by hand while holding the suspension spring; if you feel vibration through the coil spring, the bearing race is pitted.
STEP 03 Wheel Mount

Hub Centricity & Center Bore Fitment

If the vehicle has aftermarket rims, inspect whether hub centric adapter rings are installed between the wheel spigot and the vehicle hub. A gap between the hub flange and rim bore forces lug studs to support the entire vehicle weight.

Pro Test Action: Check that lug nuts seat flush. Ensure aftermarket wheels do not use OEM ball-seat lug nuts on 60° conical aftermarket wheel seats.
STEP 04 Braking System

Brake Rotor Runout & High-Speed Pulsation

Perform a moderate braking deceleration from 60 mph down to 25 mph on a smooth, empty road. If the steering wheel shudders during braking, front rotor or hub flange runout is present. If your brake pedal pulses under your foot, rear rotors or drums are distorted.

Pro Test Action: Inspect through wheel spokes for excessive rust scaling (rust jacking) between the hub face and rotor hat.
STEP 05 Tire Fitment

Wheel Well Clearance & Fender Rubbing

Turn the steering wheel to full left and right lock. Inspect the inner plastic fender liner and the front bumper corner for black scuff marks or shredded plastic. Reach behind the tire to inspect strut clearance (minimum 10mm clearance needed).

Pro Test Action: Look for cut fender lips or signs of amateur fender rolling with chipped, rusting paint along the wheel arch.
STEP 06 Electronics

TPMS Sensor Warning Lamp Cluster Test

Turn the key to ON position before cranking. The yellow horseshoe TPMS warning symbol MUST light up and turn off after engine start. If the light blinks for 60 to 90 seconds and remains solid, one or more sensors have dead batteries or missing sensors.

Pro Test Action: Never accept a seller claiming "it just needs air" if the light blinks on startup; a flashing TPMS light indicates a systemic sensor hardware fault.
STEP 07 Suspension

Shock & Strut Hydraulic Fluid Leaks

Use a flashlight to look through the wheel well at the body of each shock absorber and strut. A thin film of dry dust is normal, but wet, oily fluid running down the damper tube means the seal has blown and replacement is required in pairs.

Pro Test Action: Push down aggressively on each corner of the car and release. The vehicle should rebound and settle immediately. Bouncing more than once confirms dead struts.
STEP 08 Fasteners

Lug Nut Torque & Stud Thread Inspection

Inspect lug studs for cross-threading, stripped threads, or missing lug nuts. Verify that all lug nuts match. Aftermarket wheels installed with mismatched lug nuts or missing lug studs create catastrophic wheel separation hazards.

Pro Test Action: Bring a torque wrench set to the factory spec. Verify all lugs are properly torqued and none are stripped or spinning freely.
Essential Equipment

Pre-Purchase Inspector Field Toolkit

Take these compact tools with you to the dealership or private seller test drive to detect hidden defects.

❓ Pre-Purchase Inspection Frequently Asked Questions

PEOPLE ALSO ASK
Q: How do I test for a bad wheel bearing during a pre-purchase inspection? ▼
On the test drive, listen for a low-pitch humming or growling noise that intensifies when loading the opposite side during turns (e.g., swerving gently left loads the right bearing). When parked, raise the wheel off the ground and grab the tire at 12 and 6 o’clock positions; any detectable play indicates a failing wheel bearing or ball joint.
Q: Why does the car vibrate between 50 and 70 mph after aftermarket wheels are fitted? ▼
The most common cause is missing hub centric rings. Most aftermarket wheels feature an enlarged universal center bore (such as 73.1mm), whereas the vehicle hub requires a tight tolerance (e.g., 64.1mm or 56.1mm). Without hub centric rings, the wheel is lug-centric and off-center by fractions of a millimeter, inducing high-speed vibration.
Q: Are wheel spacers safe or should they raise red flags when buying a used car? ▼
Thin slip-on spacers without extended lug studs are dangerous because they reduce thread engagement (minimum 6.5 to 8 full turns required). Cheap non-hubcentric bolt-on spacers can loosen or shear studs under heavy load. If buying a vehicle with spacers, verify they are high-grade billet aluminum and hubcentric, or negotiate the price down to remove them.
Q: How do I know if the seller cleared an active TPMS or ABS warning light? ▼
Turn the ignition key to ON (without starting the engine). Verify that the TPMS and ABS dash warning lights illuminate for 3–5 seconds as a self-test bulb check. If the bulb does not illuminate at all, the seller may have removed or taped over the cluster LED. Plug an OBD2 scanner into the port to scan for pending ABS/TPMS fault codes.