FitmentSpec Logo
Acura logo
3rd/4th Gen UA6/UA7/UA8 (Type-S / SH-AWD 6MT) (2004–2014)

2008 Acura TL

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2008 Acura TL
Factory Powertrain 3.7L SOHC VTEC V6 (305 hp / 273 lb-ft) / 3.5L V6 Type-S (286 hp)
305 HP
Chassis Dimensions Exterior & Curb Weight
WB: 109.3"
Bolt Pattern5-Lug
5x120
Center BoreHub Centric
64.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+45 to +55
Flush Target: ET +48
Lug TorqueM14 x 1.5
94 ft-lbs
127 Nm • Ball Seat
Fastener: Ball Seat R14 Radius Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2008 Acura TL Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 1,000 lbs
Max Towing (Braked)
1,000 lbs
454 kg
With factory trailer brakes
Max Payload Capacity
850 lbs
386 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
100 lbs
45 kg
Maximum hitch downward load
Hitch Receiver Class
Class I (1.25-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2008 TL
Selected Load: 1,000 lbs • Vehicle Rating: 1,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Light duty towing up to 1,000 lbs. Recommended primarily for hitch-mounted accessories (bike racks, ski racks, cargo baskets).

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 350 lbs (159 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2008 Acura TL Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2008 Acura TL? The factory bolt pattern is 5x120 (5-lug) with a 64.1 mm center bore. The manufacturer specified wheel lug torque is 94 ft-lbs (127 Nm) using M14 x 1.5 Lug Nuts with a Ball Seat R14 Radius seating surface. Safe wheel offset range is +45mm to +55mm.

Factory OEM Wheel & Tire Configurations (2008)

1 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
TL SH-AWD HPT (19" 5-Spoke Diamond-Cut Wheels) 19x8 ET+55
245/40ZR19 Compare ⚡
35 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Acura TL factory 64.1 mm hub snout.

Factory Hub: 64.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +9.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 64.1mm (OD: 73.1mm / ID: 64.1mm)
🛒 Order 73.1mm to 64.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 8" ET55
New Wheel Width:9.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET45 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x120
2004-2014 FITMENT SPECIFICATION

2008 Acura TL

fitmentspec.com/acura/tl/2008
FINAL TORQUE94 ft-lbs(127 Nm)
Bolt Pattern (PCD)5x120
Center Bore64.1 mm
Fastener & ThreadM14 x 1.5Lug Nut • Ball Seat R14 Radius
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x120 bolt pattern and 64.1 mm hub bore.

✓ No Centering Rings Required
2024-202664.1 mm CB
Acura Integra Type S
Torque: 94 ft-lbsSpecs →
2022-202664.1 mm CB
Acura MDX
Torque: 94 ft-lbsSpecs →
2017-202264.1 mm CB
Acura NSX
Torque: 94 ft-lbsSpecs →
2014-202064.1 mm CB
Acura RLX
Torque: 94 ft-lbsSpecs →
2021-202664.1 mm CB
Acura TLX
Torque: 94 ft-lbsSpecs →
2023-202664.1 mm CB
Honda Civic Type R
Torque: 94 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +5.99" (+22.43%)
+22.43%
Original Baseline Tire245/40R19
New Target Tire285/70R17
QUICK SIZES:
26.7"32.7"
Speedometer Variance Table
30 mph gauge36.7 actual+6.7 mph
45 mph gauge55.1 actual+10.1 mph
60 mph gauge73.5 actual+13.5 mph
70 mph gauge85.7 actual+15.7 mph
80 mph gauge97.9 actual+17.9 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
215/55R17
Mounted on 17x7.0" Wheel
PCD: 5x120
Center Bore: 64.1 mm
🛡️ Technical Benefits for 2008 Acura TL
⛷️ Higher Ground Pressure
A narrower tire (215mm vs 235mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Auto-Relearn Drive Cycle
Relearn Sequence0 / 1 Steps Complete
1
Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2008 TL

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2008 Acura TL)

8 Verified Q&As
Q What is the bolt pattern for a 2008 Acura TL?
The factory bolt pattern (PCD) for the 2008 Acura TL is 5x120 (5-lug configuration) with a pitch circle diameter of 120 mm. Center bore hub diameter is 64.1 mm.
Q What is the wheel lug torque specification for a 2008 Acura TL?
The official factory wheel lug torque specification for the 2008 Acura TL is 94 ft-lbs (127 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2008 Acura TL?
The official maximum braked towing capacity for the 2008 Acura TL is 1,000 lbs (454 kg) with a maximum tongue weight limit of 100 lbs. Recommended hitch receiver: Class I (1.25-inch Receiver). Unbraked trailer limit is 350 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2008 Acura TL?
Factory stock tire sizing for the 2008 Acura TL is 245/40ZR19 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2008 Acura TL and are hub centric rings needed?
The center bore diameter is exactly 64.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 64.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2008 Acura TL use?
The 2008 Acura TL utilizes M14 x 1.5 Lug Nuts with a Ball Seat R14 Radius seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2008 Acura TL have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn Drive Cycle: Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
Q What aftermarket wheel offset and tire sizes fit a 2008 Acura TL without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +45mm and +55mm with a flush target of ET +48. Always test clearance at full steering lock.