FitmentSpec Logo
Audi logo
1st & 2nd Gen 8X/GB (SE / Sport / S Line / Black Edition / Citycarver) (2011–2026)

2016 Audi A1

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2016 Audi A1
Factory Powertrain 1.0L / 1.5L TFSI Turbocharged DOHC Inline-3/Inline-4
150 HP (110 kW) 184 lb-ft 1.5L Inline-4
Chassis Dimensions Exterior & Curb Weight
L: 158.6" W: 68.5" WB: 100.9" 2,436 – 2,789 lbs lbs
Bolt Pattern5-Lug
5x100
Center BoreHub Centric
57.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+35 to +46
Flush Target: ET +35
Lug TorqueM14x1.5
89 ft-lbs
120 Nm • Ball Seat
Fastener: Ball Seat Lug Bolt. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2016 Audi A1 Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 2,645 lbs
Max Towing (Braked)
2,645 lbs
1,200 kg
With factory trailer brakes
Max Payload Capacity
900 lbs
408 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
265 lbs
120 kg
Maximum hitch downward load
Hitch Receiver Class
Class III (2-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2016 A1
Selected Load: 2,645 lbs • Vehicle Rating: 2,645 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Adhere to factory towing manual limits and trailer tongue weight balance.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 926 lbs (420 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2016 Audi A1 Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2016 Audi A1? The factory bolt pattern is 5x100 (5-lug) with a 57.1 mm center bore. The manufacturer specified wheel lug torque is 89 ft-lbs (120 Nm) using M14x1.5 Lug Bolts with a Ball Seat seating surface. Safe wheel offset range is +35mm to +46mm.

Factory OEM Wheel & Tire Configurations (2016)

3 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
15" SE / Technik Alloy 15x6 ET+35
185/65R15 Compare ⚡
32 / 30 PSI Find Tires →
16" Sport Alloy 16x6.5 ET+40
195/55R16 Compare ⚡
33 / 30 PSI Find Tires →
17" S Line / Black Edition Alloy 17x7.5 ET+46
215/45R17 Compare ⚡
35 / 32 PSI Find Tires →

🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues

1 DOCUMENTED ISSUES
Coolant Thermostat & Water Pump (TFSI) Moderate Severity
Symptom

Minor coolant loss warning light with sweet coolant smell under hood

Root Cause & TSB Details

Plastic thermostat housing gasket seal degradation from thermal cycling

Affected Components: Thermostat Housing GasketWater Pump AssemblyExpansion Tank Cap
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Audi A1 factory 57.1 mm hub snout.

Factory Hub: 57.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +16.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 57.1mm (OD: 73.1mm / ID: 57.1mm)
🛒 Order 73.1mm to 57.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 6" ET35
New Wheel Width:7.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET25 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x100
2011-2026 FITMENT SPECIFICATION

2016 Audi A1

fitmentspec.com/audi/a1/2016
FINAL TORQUE89 ft-lbs(120 Nm)
Bolt Pattern (PCD)5x100
Center Bore57.1 mm
Fastener & ThreadM14x1.5Lug Bolt • Ball Seat
TPMS CalibrationIndirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +8.24" (+33.68%)
+33.68%
Original Baseline Tire185/65R15
New Target Tire285/70R17
QUICK SIZES:
24.5"32.7"
Speedometer Variance Table
30 mph gauge40.1 actual+10.1 mph
45 mph gauge60.2 actual+15.2 mph
60 mph gauge80.2 actual+20.2 mph
70 mph gauge93.6 actual+23.6 mph
80 mph gauge106.9 actual+26.9 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
205/70R16
Mounted on 16x6.5" Wheel
PCD: 5x100
Center Bore: 57.1 mm
🛡️ Technical Benefits for 2016 Audi A1
⛷️ Higher Ground Pressure
A narrower tire (205mm vs 185mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

INDIRECT TPMSABS Wheel Speed Based
Architecture
Indirect Wheel Speed ABS
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Cluster-Reset
Relearn Sequence0 / 4 Steps Complete
1
Inflate all tires to the placard values located inside driver B-pillar.
2
Switch ignition ON with the car stationary.
3
Access Audi MMI: Car > Vehicle Settings > Servicing & Checks > Tyre Pressure Loss Indicator > Store Tyre Pressures.
4
Confirm 'Yes, store now' and drive for 15-20 minutes to complete indirect ABS sensor recalibration.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →

🔍 Pre-Purchase Fitment & Chassis Inspection Checklist

Universal 8-Point Buyer Guide →

✓ Wheel Hub & Bearing Inspection

  • • Verify 57.1mm hub spigot is free of oxidation prior to installing aftermarket wheels.
  • • CRITICAL: Audi factory wheels require R13 spherical Ball Seat lug bolts (M14x1.5); aftermarket alloy wheels require 60° Conical seat bolts. Never mix fastener seat types.

✓ Suspension & Steering Clearance

  • • Check inner clearance to front MacPherson struts on 8.0-inch or wider wheels.
  • • Inspect rear torsion beam axle mounting bushings for signs of tearing or perished rubber.
Brake Caliper Clearance Note

Front single-piston calipers clear all OEM 15-inch and 16-inch wheels easily; S1 or upgraded 310mm brakes require minimum 17-inch wheels.

Common Wear Replacement Parts

📋 One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

🔩

Verified Hardware & Installation Kit for 2016 A1

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2016 Audi A1)

8 Verified Q&As
Q What is the bolt pattern for a 2016 Audi A1?
The factory bolt pattern (PCD) for the 2016 Audi A1 is 5x100 (5-lug configuration) with a pitch circle diameter of 100 mm. Center bore hub diameter is 57.1 mm.
Q What is the wheel lug torque specification for a 2016 Audi A1?
The official factory wheel lug torque specification for the 2016 Audi A1 is 89 ft-lbs (120 Nm). Tighten all Lug Bolts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2016 Audi A1?
The official maximum braked towing capacity for the 2016 Audi A1 is 2,645 lbs (1,200 kg) with a maximum tongue weight limit of 265 lbs. Recommended hitch receiver: Class III (2-inch Receiver). Unbraked trailer limit is 926 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2016 Audi A1?
Factory stock tire sizing for the 2016 Audi A1 is 185/65R15 with a recommended cold tire pressure of 32 PSI front and 30 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2016 Audi A1 and are hub centric rings needed?
The center bore diameter is exactly 57.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 57.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2016 Audi A1 use?
The 2016 Audi A1 utilizes M14x1.5 Lug Bolts with a Ball Seat seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2016 Audi A1 have Direct or Indirect TPMS and how is it reset?
It uses an Indirect TPMS system that calculates relative pressure by monitoring individual wheel rotation speeds via the ABS wheel speed sensors. Reset procedure: Cluster-Reset.
Q What aftermarket wheel offset and tire sizes fit a 2016 Audi A1 without rubbing?
For an aggressive yet flush aesthetic without fender rolling or rubbing, the recommended setup is 17x7.5 ET38 wheels with 215/45R17 tires. For a 100% rub-free conservative upgrade, choose 16x7.0 ET38 with 205/50R16. Factory safe offset range spans +35mm to +46mm.

⚠️ Official NHTSA Safety Recalls & Bulletins

NHTSA #20V451000 • Suspension: Front Wishbone / Track Control Arm

Audi issued recall campaign for certain MQB A0 models due to front lower control arm welding inspection requirements.

Remedy: Authorized Audi dealers inspect lower wishbones and replace affected assemblies free of charge.