FitmentSpec Logo
Chevrolet logo
8th Gen (C8) (2020–2026)

2022 Chevrolet Corvette

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2022 Chevrolet Corvette
Factory Powertrain 6.2L LT2 Small Block Mid-Engine V8
495 HP (369 kW) 470 lb-ft 6.2L V8
Chassis Dimensions Exterior & Curb Weight
L: 182.3" W: 76.1" WB: 107.2" 3,366 – 3,647 lbs lbs
Bolt Pattern5-Lug
5x120
Center BoreHub Centric
66.9 mm
Hub Ring Spigot Diameter
Offset RangeET
+45 to +54
Flush Target: ET +38
Lug TorqueM14x1.5
140 ft-lbs
190 Nm • Conical Seat
Fastener: Conical 60° Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2022 Chevrolet Corvette Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Towing Not Recommended
Max Towing (Braked)
0 lbs
Not Certified
Factory sports chassis
Max Payload Capacity
550 lbs
249 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
0 lbs
0 kg
Maximum hitch downward load
Hitch Receiver Class
Not Recommended for Towing
Standard bumper / ball mount
📋 Factory Towing Guidance:

Manufacturer does not certify or recommend this performance chassis for trailer towing. Hitch installation is unsupported and may void warranty.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 0 lbs (0 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2022 Chevrolet Corvette Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2022 Chevrolet Corvette? The factory bolt pattern is 5x120 (5-lug) with a 66.9 mm center bore. The manufacturer specified wheel lug torque is 140 ft-lbs (190 Nm) using M14x1.5 Lug Nuts with a Conical 60° seating surface. Safe wheel offset range is +45mm to +54mm.

Factory OEM Wheel & Tire Configurations (2022)

1 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
Stingray Z51 19x8.5 ET+52
245/35ZR19 Compare ⚡
30 / 30 PSI Find Tires →

🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues

1 DOCUMENTED ISSUES
Wheels & Hub Clearance Moderate Severity
Symptom

Slow tire pressure loss without puncture; vibration at 70+ mph on aftermarket setups

Root Cause & TSB Details

Micro-porosity or hairline stress fractures along the inner barrel lip under high lateral G loads (GM Technical Bulletin 20-NA-189)

Affected Components: OEM Cast Aluminum WheelsTPMS Stem SealHub Flange Runout
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Chevrolet Corvette factory 66.9 mm hub snout.

Factory Hub: 66.9mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +6.2 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 66.9mm (OD: 73.1mm / ID: 66.9mm)
🛒 Order 73.1mm to 66.9mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 8.5" ET52
New Wheel Width:9.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET42 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x120
2020-2026 FITMENT SPECIFICATION

2022 Chevrolet Corvette

fitmentspec.com/chevrolet/corvette/2022
FINAL TORQUE140 ft-lbs(190 Nm)
Bolt Pattern (PCD)5x120
Center Bore66.9 mm
Fastener & ThreadM14x1.5Lug Nut • Conical 60°
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x120 bolt pattern and 66.9 mm hub bore.

✓ No Centering Rings Required
2020-202667.1 mm CB
Cadillac CT5
Torque: 140 ft-lbsSpecs →
2022-202666.9 mm CB
Cadillac CT5-V Blackwing
Torque: 140 ft-lbsSpecs →
2016-202466.9 mm CB
Chevrolet Camaro
Torque: 140 ft-lbsSpecs →
2016-202466.9 mm CB
Chevrolet Camaro
Torque: 140 ft-lbsSpecs →
2014-202066.9 mm CB
Chevrolet Impala
Torque: 140 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +6.96" (+27.01%)
+27.01%
Original Baseline Tire245/35R19
New Target Tire285/70R17
QUICK SIZES:
25.8"32.7"
Speedometer Variance Table
30 mph gauge38.1 actual+8.1 mph
45 mph gauge57.2 actual+12.2 mph
60 mph gauge76.2 actual+16.2 mph
70 mph gauge88.9 actual+18.9 mph
80 mph gauge101.6 actual+21.6 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
215/55R17
Mounted on 17x7.5" Wheel
PCD: 5x120
Center Bore: 66.9 mm
🛡️ Technical Benefits for 2022 Chevrolet Corvette
⛷️ Higher Ground Pressure
A narrower tire (215mm vs 235mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
GM 433MHz
Relearn Protocol
Auto-Relearn
Relearn Sequence0 / 2 Steps Complete
1
Inflate cold tires to door placard pressure.
2
Drive for 15 minutes above 20 mph.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →

🔍 Pre-Purchase Fitment & Chassis Inspection Checklist

Universal 8-Point Buyer Guide →

✓ Wheel Hub & Bearing Inspection

  • • Check 12 and 6 o'clock hub bearing play

✓ Suspension & Steering Clearance

  • • Inspect front strut clearance
Brake Caliper Clearance Note

Factory caliper clearance notes

Common Wear Replacement Parts

📋 One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

🔩

Verified Hardware & Installation Kit for 2022 Corvette

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2022 Chevrolet Corvette)

8 Verified Q&As
Q What is the bolt pattern for a 2022 Chevrolet Corvette?
The factory bolt pattern (PCD) for the 2022 Chevrolet Corvette is 5x120 (5-lug configuration) with a pitch circle diameter of 120 mm. Center bore hub diameter is 66.9 mm.
Q What is the wheel lug torque specification for a 2022 Chevrolet Corvette?
The official factory wheel lug torque specification for the 2022 Chevrolet Corvette is 140 ft-lbs (190 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2022 Chevrolet Corvette?
The manufacturer does not rate or recommend the 2022 Chevrolet Corvette for trailer towing. Installing an aftermarket trailer hitch receiver is not advised for towing loads and may void powertrain warranty.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2022 Chevrolet Corvette?
Factory stock tire sizing for the 2022 Chevrolet Corvette is 245/35ZR19 with a recommended cold tire pressure of 30 PSI front and 30 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2022 Chevrolet Corvette and are hub centric rings needed?
The center bore diameter is exactly 66.9 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 66.9mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2022 Chevrolet Corvette use?
The 2022 Chevrolet Corvette utilizes M14x1.5 Lug Nuts with a Conical 60° seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2022 Chevrolet Corvette have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn: Inflate cold tires to door placard pressure.
Q What aftermarket wheel offset and tire sizes fit a 2022 Chevrolet Corvette without rubbing?
For an aggressive yet flush aesthetic without fender rolling or rubbing, the recommended setup is 18x8.5 ET40 wheels with 245/40R18 tires. For a 100% rub-free conservative upgrade, choose 18x8.0 ET45 with 235/45R18. Factory safe offset range spans +45mm to +54mm.