FitmentSpec Logo
Chevrolet logo
3rd Gen (2024–2026)

2026 Chevrolet Traverse

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2026 Chevrolet Traverse
Factory Powertrain 2.5L Turbocharged DOHC 4-Cylinder
328 HP (245 kW) 326 lb-ft 2.5L Inline-4 Turbo
Chassis Dimensions Exterior & Curb Weight
L: 204.5" W: 79.6" WB: 121" 4,630 - 4,890 lbs lbs
Bolt Pattern6-Lug
6x120
Center BoreHub Centric
66.9 mm
Hub Ring Spigot Diameter
Offset RangeET
+35 to +50
Flush Target: ET +35
Lug TorqueM14 x 1.5
140 ft-lbs
190 Nm • Conical Seat
Fastener: Conical 60 Degree Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2026 Chevrolet Traverse Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 5,000 lbs
Max Towing (Braked)
5,000 lbs
2,268 kg
With factory trailer brakes
Max Payload Capacity
1,540 lbs
699 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
500 lbs
227 kg
Maximum hitch downward load
Hitch Receiver Class
Class III (2-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2026 Traverse
Selected Load: 5,000 lbs • Vehicle Rating: 5,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

5,000 lbs with available Trailering Package (V92) on 2.5L Turbo 4-cylinder engine.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 1500 lbs (680 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2026 Chevrolet Traverse Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2026 Chevrolet Traverse? The factory bolt pattern is 6x120 (6-lug) with a 66.9 mm center bore. The manufacturer specified wheel lug torque is 140 ft-lbs (190 Nm) using M14 x 1.5 Lug Nuts with a Conical 60 Degree seating surface. Safe wheel offset range is +35mm to +50mm.

Factory OEM Wheel & Tire Configurations (2026)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
LT / Z71 (18" All-Terrain Rugged) 18x8 ET+45
265/65R18 (Goodyear Wrangler Territory A/T) Compare ⚡
36 PSI Find Tires →
RS (22" High-Gloss Black) 22x8.5 ET+45
275/45R22 Compare ⚡
36 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Chevrolet Traverse factory 66.9 mm hub snout.

Factory Hub: 66.9mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +6.2 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 66.9mm (OD: 73.1mm / ID: 66.9mm)
🛒 Order 73.1mm to 66.9mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 8" ET45
New Wheel Width:9.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET35 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

6x120
2024-2026 FITMENT SPECIFICATION

2026 Chevrolet Traverse

fitmentspec.com/chevrolet/traverse/2026
FINAL TORQUE140 ft-lbs(190 Nm)
Bolt Pattern (PCD)6x120
Center Bore66.9 mm
Fastener & ThreadM14 x 1.5Lug Nut • Conical 60 Degree
TPMS CalibrationDirect Tire Pressure Sensor with Tire Fill AlertDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 6x120 bolt pattern and 66.9 mm hub bore.

✓ No Centering Rings Required
2024-202667.1 mm CB
Acura ZDX
Torque: 140 ft-lbsSpecs →
2022-202666.9 mm CB
Buick Enclave
Torque: 140 ft-lbsSpecs →
2023-202666.9 mm CB
Cadillac Lyriq
Torque: 140 ft-lbsSpecs →
2019-202666.9 mm CB
Chevrolet Blazer
Torque: 140 ft-lbsSpecs →
2024-202666.9 mm CB
GMC Acadia
Torque: 140 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Significant DifferenceDiameter: +1.15" (+3.63%)
+3.63%
Original Baseline Tire265/65R18
New Target Tire285/70R17
QUICK SIZES:
31.6"32.7"
Speedometer Variance Table
30 mph gauge31.1 actual+1.1 mph
45 mph gauge46.6 actual+1.6 mph
60 mph gauge62.2 actual+2.2 mph
70 mph gauge72.5 actual+2.5 mph
80 mph gauge82.9 actual+2.9 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
255/70R17
Mounted on 17x7.0" Wheel
PCD: 6x120
Center Bore: 66.9 mm
🛡️ Technical Benefits for 2026 Chevrolet Traverse
⛷️ Higher Ground Pressure
A narrower tire (255mm vs 265mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TIRE PRESSURE SENSOR WITH TIRE FILL ALERT TPMS433 MHz
Architecture
Indirect Wheel Speed ABS
Sensor Part Number
13598773
Relearn Protocol
DIC Relearn / GM Tool
Relearn Sequence0 / 1 Steps Complete
1
Enter learn mode in cluster settings. Trigger LF, RF, RR, LR sensors sequentially until horn double-chirps.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2026 Traverse

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2026 Chevrolet Traverse)

8 Verified Q&As
Q What is the bolt pattern for a 2026 Chevrolet Traverse?
The factory bolt pattern (PCD) for the 2026 Chevrolet Traverse is 6x120 (6-lug configuration) with a pitch circle diameter of 120 mm. Center bore hub diameter is 66.9 mm.
Q What is the wheel lug torque specification for a 2026 Chevrolet Traverse?
The official factory wheel lug torque specification for the 2026 Chevrolet Traverse is 140 ft-lbs (190 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2026 Chevrolet Traverse?
The official maximum braked towing capacity for the 2026 Chevrolet Traverse is 5,000 lbs (2,268 kg) with a maximum tongue weight limit of 500 lbs. Recommended hitch receiver: Class III (2-inch Receiver). Unbraked trailer limit is 1,500 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2026 Chevrolet Traverse?
Factory stock tire sizing for the 2026 Chevrolet Traverse is 265/65R18 (Goodyear Wrangler Territory A/T) with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2026 Chevrolet Traverse and are hub centric rings needed?
The center bore diameter is exactly 66.9 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 66.9mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2026 Chevrolet Traverse use?
The 2026 Chevrolet Traverse utilizes M14 x 1.5 Lug Nuts with a Conical 60 Degree seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2026 Chevrolet Traverse have Direct or Indirect TPMS and how is it reset?
This vehicle utilizes standard valve stems without requiring active electronic TPMS sensor recalibration.
Q What aftermarket wheel offset and tire sizes fit a 2026 Chevrolet Traverse without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +35mm and +50mm with a flush target of ET +35. Always test clearance at full steering lock.