FitmentSpec Logo
Dodge logo
8th Gen (LB / Daytona EV & Sixpack) (2024–2026)

2025 Dodge Charger

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2025 Dodge Charger
Factory Powertrain Dual Electric Motors (Daytona R/T 496 HP / Scat Pack 670 HP) & 3.0L Hurricane I6
670 HP (500 kW) 627 lb-ft 0 Dual-Motor AWD EV
Chassis Dimensions Exterior & Curb Weight
L: 206.6" W: 79.8" WB: 121" 5,698 – 5,838 lbs (Daytona EV) lbs
Bolt Pattern5-Lug
5x127
Center BoreHub Centric
71.5 mm
Hub Ring Spigot Diameter
Offset RangeET
+15 to +45
Flush Target: ET +20
Lug TorqueM14x1.5
130 ft-lbs
176 Nm • Conical Seat
Fastener: Conical 60° Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2025 Dodge Charger Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Towing Not Recommended
Max Towing (Braked)
0 lbs
Not Certified
Factory sports chassis
Max Payload Capacity
850 lbs
386 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
0 lbs
0 kg
Maximum hitch downward load
Hitch Receiver Class
Not Rated for Towing
Standard bumper / ball mount
📋 Factory Towing Guidance:

Stellantis does not rate the 8th-gen Dodge Charger Daytona EV for trailer towing.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 0 lbs (0 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2025 Dodge Charger Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2025 Dodge Charger? The factory bolt pattern is 5x127 (5-lug) with a 71.5 mm center bore. The manufacturer specified wheel lug torque is 130 ft-lbs (176 Nm) using M14x1.5 Lug Nuts with a Conical 60° seating surface. Safe wheel offset range is +15mm to +45mm.

Factory OEM Wheel & Tire Configurations (2025)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
Daytona R/T (18" / 20" Aluminum) 20x9 ET+42
255/45R20 Compare ⚡
38 / 38 PSI Find Tires →
Daytona Scat Pack Track Package (20" Staggered Widebody) 20x11 ET+20
305/35ZR20 Compare ⚡
39 / 39 PSI Find Tires →

🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues

2 DOCUMENTED ISSUES
STLA Large 5x127 (5x5") Bolt Pattern Transition High Severity
Symptom

Older 5x115 Charger/Challenger wheels failing to bolt onto 2024–2026 Charger Daytona hubs

Root Cause & TSB Details

STLA Large switched from Chrysler's legacy 5x115 PCD (LX/LD) to 5x127 (5x5") with 71.5mm hub bore to support 5,838 lb EV axle loads.

Affected Components: 5x127 Wheel HubsM14x1.5 Lug Hardware
High-Weight EV Tire Shoulder Wear Moderate Severity
Symptom

Rapid outer/inner edge wear on 305/35ZR20 & 325/35ZR20 Goodyear Eagle F1 tires

Root Cause & TSB Details

5,838 lb curb weight combined with 627 lb-ft instantaneous dual-motor torque accelerates tread wear during aggressive launches.

Affected Components: 305/35ZR20 & 325/35ZR20 TiresFront/Rear Toe Alignment
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Dodge Charger factory 71.5 mm hub snout.

Factory Hub: 71.5mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +1.6 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 71.5mm (OD: 73.1mm / ID: 71.5mm)
🛒 Order 73.1mm to 71.5mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 9" ET42
New Wheel Width:10.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET32 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x127
2024-2026 FITMENT SPECIFICATION

2025 Dodge Charger

fitmentspec.com/dodge/charger/2025
FINAL TORQUE130 ft-lbs(176 Nm)
Bolt Pattern (PCD)5x127
Center Bore71.5 mm
Fastener & ThreadM14x1.5Lug Nut • Conical 60°
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x127 bolt pattern and 71.5 mm hub bore.

✓ No Centering Rings Required
2020-202672.6 mm CB
Land Rover Defender
Torque: 130 ft-lbsSpecs →
2020-202672.6 mm CB
Land Rover Defender 110
Torque: 130 ft-lbsSpecs →
2017-202672.6 mm CB
Land Rover Discovery
Torque: 130 ft-lbsSpecs →
2022-202672.6 mm CB
Land Rover Range Rover
Torque: 130 ft-lbsSpecs →
2023-202672.6 mm CB
Land Rover Range Rover Sport
Torque: 130 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +3.67" (+12.65%)
+12.65%
Original Baseline Tire255/45R20
New Target Tire285/70R17
QUICK SIZES:
29.0"32.7"
Speedometer Variance Table
30 mph gauge33.8 actual+3.8 mph
45 mph gauge50.7 actual+5.7 mph
60 mph gauge67.6 actual+7.6 mph
70 mph gauge78.9 actual+8.9 mph
80 mph gauge90.1 actual+10.1 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
235/55R18
Mounted on 18x8.0" Wheel
PCD: 5x127
Center Bore: 71.5 mm
🛡️ Technical Benefits for 2025 Dodge Charger
⛷️ Higher Ground Pressure
A narrower tire (235mm vs 255mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
68339096AB
Relearn Protocol
Auto-Relearn
Relearn Sequence0 / 3 Steps Complete
1
Inflate all four tires to door-jamb placard cold pressure (38 PSI R/T; 39 PSI Scat Pack).
2
Drive vehicle continuously for 15 to 20 minutes above 20 mph (32 km/h).
3
The STLA Large RF receiver automatically pairs sensor IDs and updates Uconnect 5 cluster readouts.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →

🔍 Pre-Purchase Fitment & Chassis Inspection Checklist

Universal 8-Point Buyer Guide →

✓ Wheel Hub & Bearing Inspection

  • • Confirm 5x127 (5x5") hub flange is clean and all M14x1.5 lug fasteners are torqued to 130 ft-lbs (176 Nm).
  • • Inspect 71.5mm hub spigot and rear wheel bearings for play under heavy EV curb load.

✓ Suspension & Steering Clearance

  • • Verify Track Package adaptive dampers and 305/325 staggered tires for uneven inner shoulder wear or curb impact.
  • • Check underbody battery shield and front R-Wing aerodynamic splitter for scraping.
Brake Caliper Clearance Note

Scat Pack Track Package 16-inch (410mm) Brembo 6-piston front rotors and calipers require 20-inch wheels with deep caliper clearance barrels.

Common Wear Replacement Parts

📋 One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

🔩

Verified Hardware & Installation Kit for 2025 Charger

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2025 Dodge Charger)

8 Verified Q&As
Q What is the bolt pattern for a 2025 Dodge Charger?
The factory bolt pattern (PCD) for the 2025 Dodge Charger is 5x127 (5-lug configuration) with a pitch circle diameter of 127 mm. Center bore hub diameter is 71.5 mm.
Q What is the wheel lug torque specification for a 2025 Dodge Charger?
The official factory wheel lug torque specification for the 2025 Dodge Charger is 130 ft-lbs (176 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2025 Dodge Charger?
The manufacturer does not rate or recommend the 2025 Dodge Charger for trailer towing. Installing an aftermarket trailer hitch receiver is not advised for towing loads and may void powertrain warranty.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2025 Dodge Charger?
Factory stock tire sizing for the 2025 Dodge Charger is 255/45R20 with a recommended cold tire pressure of 38 PSI front and 38 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2025 Dodge Charger and are hub centric rings needed?
The center bore diameter is exactly 71.5 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 71.5mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2025 Dodge Charger use?
The 2025 Dodge Charger utilizes M14x1.5 Lug Nuts with a Conical 60° seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2025 Dodge Charger have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn: Inflate all four tires to door-jamb placard cold pressure (38 PSI R/T; 39 PSI Scat Pack).
Q What aftermarket wheel offset and tire sizes fit a 2025 Dodge Charger without rubbing?
For an aggressive yet flush aesthetic without fender rolling or rubbing, the recommended setup is 20x11.0 ET+20 wheels with 305/35ZR20 tires. For a 100% rub-free conservative upgrade, choose 20x9.5 ET+30 with 275/40R20. Factory safe offset range spans +15mm to +45mm.

⚠️ Official NHTSA Safety Recalls & Bulletins

NHTSA #25V-389 • EXTERIOR WARNING SOUND / AMPLIFIER SOFTWARE

FCA Recall 44C: Certain 2024–2025 Dodge Charger Daytona EV units were built with incomplete amplifier software that fails to emit the required low-speed external pedestrian warning sound.

Remedy: Dealers update the amplifier software free of charge.