FitmentSpec Logo
Honda logo
5th Gen RL6 (EX / EX-L / Sport / Touring / Elite) (2018–2026)

2020 Honda Odyssey

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2020 Honda Odyssey
Factory Powertrain 3.5L i-VTEC V6 (280 hp / 262 lb-ft)
280 HP
Chassis Dimensions Exterior & Curb Weight
WB: 118.1"
Bolt Pattern5-Lug
5x120
Center BoreHub Centric
64.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+45 to +55
Flush Target: ET +48
Lug TorqueM14 x 1.5
94 ft-lbs
127 Nm • Ball Seat
Fastener: Ball Seat R14 Radius Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2020 Honda Odyssey Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 3,500 lbs
Max Towing (Braked)
3,500 lbs
1,588 kg
With factory trailer brakes
Max Payload Capacity
1,530 lbs
694 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
350 lbs
159 kg
Maximum hitch downward load
Hitch Receiver Class
Class II (2-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2020 Odyssey
Selected Load: 3,500 lbs • Vehicle Rating: 3,500 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

3,500 lbs towing capacity with 3.5L V6; accessory transmission cooler recommended when towing near maximum limit or in mountainous terrain.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 1225 lbs (556 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2020 Honda Odyssey Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2020 Honda Odyssey? The factory bolt pattern is 5x120 (5-lug) with a 64.1 mm center bore. The manufacturer specified wheel lug torque is 94 ft-lbs (127 Nm) using M14 x 1.5 Lug Nuts with a Ball Seat R14 Radius seating surface. Safe wheel offset range is +45mm to +55mm.

Factory OEM Wheel & Tire Configurations (2020)

1 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
Elite (19" Gloss Black Machined Finish Wheels) 19x7.5 ET+50
235/55R19 Compare ⚡
35 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Honda Odyssey factory 64.1 mm hub snout.

Factory Hub: 64.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +9.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 64.1mm (OD: 73.1mm / ID: 64.1mm)
🛒 Order 73.1mm to 64.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 7.5" ET50
New Wheel Width:8.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET40 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x120
2018-2026 FITMENT SPECIFICATION

2020 Honda Odyssey

fitmentspec.com/honda/odyssey/2020
FINAL TORQUE94 ft-lbs(127 Nm)
Bolt Pattern (PCD)5x120
Center Bore64.1 mm
Fastener & ThreadM14 x 1.5Lug Nut • Ball Seat R14 Radius
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x120 bolt pattern and 64.1 mm hub bore.

✓ No Centering Rings Required
2024-202664.1 mm CB
Acura Integra Type S
Torque: 94 ft-lbsSpecs →
2022-202664.1 mm CB
Acura MDX
Torque: 94 ft-lbsSpecs →
2017-202264.1 mm CB
Acura NSX
Torque: 94 ft-lbsSpecs →
2014-202064.1 mm CB
Acura RLX
Torque: 94 ft-lbsSpecs →
2004-201464.1 mm CB
Acura TL
Torque: 94 ft-lbsSpecs →
2021-202664.1 mm CB
Acura TLX
Torque: 94 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +3.53" (+12.10%)
+12.10%
Original Baseline Tire235/55R19
New Target Tire285/70R17
QUICK SIZES:
29.2"32.7"
Speedometer Variance Table
30 mph gauge33.6 actual+3.6 mph
45 mph gauge50.4 actual+5.4 mph
60 mph gauge67.3 actual+7.3 mph
70 mph gauge78.5 actual+8.5 mph
80 mph gauge89.7 actual+9.7 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
215/65R17
Mounted on 17x6.5" Wheel
PCD: 5x120
Center Bore: 64.1 mm
🛡️ Technical Benefits for 2020 Honda Odyssey
⛷️ Higher Ground Pressure
A narrower tire (215mm vs 235mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Auto-Relearn Drive Cycle
Relearn Sequence0 / 1 Steps Complete
1
Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2020 Odyssey

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2020 Honda Odyssey)

8 Verified Q&As
Q What is the bolt pattern for a 2020 Honda Odyssey?
The factory bolt pattern (PCD) for the 2020 Honda Odyssey is 5x120 (5-lug configuration) with a pitch circle diameter of 120 mm. Center bore hub diameter is 64.1 mm.
Q What is the wheel lug torque specification for a 2020 Honda Odyssey?
The official factory wheel lug torque specification for the 2020 Honda Odyssey is 94 ft-lbs (127 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2020 Honda Odyssey?
The official maximum braked towing capacity for the 2020 Honda Odyssey is 3,500 lbs (1,588 kg) with a maximum tongue weight limit of 350 lbs. Recommended hitch receiver: Class II (2-inch Receiver). Unbraked trailer limit is 1,225 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2020 Honda Odyssey?
Factory stock tire sizing for the 2020 Honda Odyssey is 235/55R19 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2020 Honda Odyssey and are hub centric rings needed?
The center bore diameter is exactly 64.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 64.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2020 Honda Odyssey use?
The 2020 Honda Odyssey utilizes M14 x 1.5 Lug Nuts with a Ball Seat R14 Radius seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2020 Honda Odyssey have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn Drive Cycle: Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
Q What aftermarket wheel offset and tire sizes fit a 2020 Honda Odyssey without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +45mm and +55mm with a flush target of ET +48. Always test clearance at full steering lock.