FitmentSpec Logo
Hyundai logo
LX2 (1st Gen) (2020–2026)

2025 Hyundai Palisade

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2025 Hyundai Palisade
Factory Powertrain Lambda II 3.8L GDI DOHC 24-Valve V6
291 HP (217 kW) 262 lb-ft 3.8L V6
Chassis Dimensions Exterior & Curb Weight
L: 196.7" W: 77.8" WB: 114.2" 4,127 - 4,506 lbs lbs
Center BoreHub Centric
67.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+35 to +50
Flush Target: ET +35
Lug TorqueM12 x 1.5
94 ft-lbs
127 Nm • Conical Seat
Fastener: Conical 60 Degree Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2025 Hyundai Palisade Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 5,000 lbs
Max Towing (Braked)
5,000 lbs
2,268 kg
With factory trailer brakes
Max Payload Capacity
1,571 lbs
713 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
500 lbs
227 kg
Maximum hitch downward load
Hitch Receiver Class
Class III (2-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2025 Palisade
Selected Load: 5,000 lbs • Vehicle Rating: 5,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Standard 5,000 lbs towing on all trims with 3.8L V6, standard heavy-duty transmission cooler, and Tow Mode logic.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 1500 lbs (680 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2025 Hyundai Palisade Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2025 Hyundai Palisade? The factory bolt pattern is 5x114.3 (5-lug) with a 67.1 mm center bore. The manufacturer specified wheel lug torque is 94 ft-lbs (127 Nm) using M12 x 1.5 Lug Nuts with a Conical 60 Degree seating surface. Safe wheel offset range is +35mm to +50mm.

Factory OEM Wheel & Tire Configurations (2025)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
SE / SEL (18") 18x7.5 ET+49.5
245/60R18 Compare ⚡
35 PSI Find Tires →
Limited / Calligraphy / XRT (20" Multi-Spoke) 20x7.5 ET+49.5
245/50R20 Compare ⚡
35 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Hyundai Palisade factory 67.1 mm hub snout.

Factory Hub: 67.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +6.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 67.1mm (OD: 73.1mm / ID: 67.1mm)
🛒 Order 73.1mm to 67.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 7.5" ET49.5
New Wheel Width:8.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET39.5 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x114.3
2020-2026 FITMENT SPECIFICATION

2025 Hyundai Palisade

fitmentspec.com/hyundai/palisade/2025
FINAL TORQUE94 ft-lbs(127 Nm)
Bolt Pattern (PCD)5x114.3
Center Bore67.1 mm
Fastener & ThreadM12 x 1.5Lug Nut • Conical 60 Degree
TPMS CalibrationDirect Tire Pressure SensorDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x114.3 bolt pattern and 67.1 mm hub bore.

✓ No Centering Rings Required
2007-201067.1 mm CB
Alfa Romeo 8C Competizione
Torque: 94 ft-lbsSpecs →
2022-202667.1 mm CB
Ferrari 296 GTB
Torque: 94 ft-lbsSpecs →
2010-201567.1 mm CB
Ferrari 458 Italia
Torque: 94 ft-lbsSpecs →
2016-202067.1 mm CB
Ferrari 488 GTB
Torque: 94 ft-lbsSpecs →
2018-202467.1 mm CB
Ferrari 812 Superfast
Torque: 94 ft-lbsSpecs →
2009-201767.1 mm CB
Ferrari California
Torque: 94 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +3.13" (+10.60%)
+10.60%
Original Baseline Tire245/60R18
New Target Tire285/70R17
QUICK SIZES:
29.6"32.7"
Speedometer Variance Table
30 mph gauge33.2 actual+3.2 mph
45 mph gauge49.8 actual+4.8 mph
60 mph gauge66.4 actual+6.4 mph
70 mph gauge77.4 actual+7.4 mph
80 mph gauge88.5 actual+8.5 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
235/65R17
Mounted on 17x6.5" Wheel
PCD: 5x114.3
Center Bore: 67.1 mm
🛡️ Technical Benefits for 2025 Hyundai Palisade
⛷️ Higher Ground Pressure
A narrower tire (235mm vs 245mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TIRE PRESSURE SENSOR TPMS433 MHz
Architecture
Indirect Wheel Speed ABS
Sensor Part Number
52933-C1100
Relearn Protocol
Automatic Drive Relearn
Relearn Sequence0 / 1 Steps Complete
1
Inflate all tires to placard (35 PSI). Drive vehicle at 20 mph or greater continuously for 10-15 minutes.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2025 Palisade

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2025 Hyundai Palisade)

8 Verified Q&As
Q What is the bolt pattern for a 2025 Hyundai Palisade?
The factory bolt pattern (PCD) for the 2025 Hyundai Palisade is 5x114.3 (5-lug configuration) with a pitch circle diameter of 114.3 mm. Center bore hub diameter is 67.1 mm.
Q What is the wheel lug torque specification for a 2025 Hyundai Palisade?
The official factory wheel lug torque specification for the 2025 Hyundai Palisade is 94 ft-lbs (127 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2025 Hyundai Palisade?
The official maximum braked towing capacity for the 2025 Hyundai Palisade is 5,000 lbs (2,268 kg) with a maximum tongue weight limit of 500 lbs. Recommended hitch receiver: Class III (2-inch Receiver). Unbraked trailer limit is 1,500 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2025 Hyundai Palisade?
Factory stock tire sizing for the 2025 Hyundai Palisade is 245/60R18 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2025 Hyundai Palisade and are hub centric rings needed?
The center bore diameter is exactly 67.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 67.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2025 Hyundai Palisade use?
The 2025 Hyundai Palisade utilizes M12 x 1.5 Lug Nuts with a Conical 60 Degree seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2025 Hyundai Palisade have Direct or Indirect TPMS and how is it reset?
This vehicle utilizes standard valve stems without requiring active electronic TPMS sensor recalibration.
Q What aftermarket wheel offset and tire sizes fit a 2025 Hyundai Palisade without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +35mm and +50mm with a flush target of ET +35. Always test clearance at full steering lock.