FitmentSpec Logo
Hyundai logo
QX (1st Gen) (2020–2026)

2026 Hyundai Venue

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2026 Hyundai Venue
Factory Powertrain Smartstream 1.6L MPI DOHC 16-Valve 4-Cylinder
121 HP (90 kW) 113 lb-ft 1.6L Inline-4
Chassis Dimensions Exterior & Curb Weight
L: 159.1" W: 69.7" WB: 99.2" 2,612 - 2,745 lbs lbs
Bolt Pattern4-Lug
4x100
Center BoreHub Centric
54.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+38 to +50
Flush Target: ET +40
Lug TorqueM12 x 1.5
80 ft-lbs
110 Nm • Conical Seat
Fastener: Conical 60 Degree Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2026 Hyundai Venue Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 1,000 lbs
Max Towing (Braked)
1,000 lbs
454 kg
With factory trailer brakes
Max Payload Capacity
850 lbs
386 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
100 lbs
45 kg
Maximum hitch downward load
Hitch Receiver Class
Class I (1.25-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2026 Venue
Selected Load: 1,000 lbs • Vehicle Rating: 1,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Light duty towing up to 1,000 lbs. Recommended primarily for hitch-mounted accessories (bike racks, ski racks, cargo baskets).

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 350 lbs (159 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2026 Hyundai Venue Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2026 Hyundai Venue? The factory bolt pattern is 4x100 (4-lug) with a 54.1 mm center bore. The manufacturer specified wheel lug torque is 80 ft-lbs (110 Nm) using M12 x 1.5 Lug Nuts with a Conical 60 Degree seating surface. Safe wheel offset range is +38mm to +50mm.

Factory OEM Wheel & Tire Configurations (2026)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
SE 15x6 ET+47
185/65R15 Compare ⚡
33 PSI Find Tires →
SEL / Limited 17x6.5 ET+50
205/55R17 Compare ⚡
33 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Hyundai Venue factory 54.1 mm hub snout.

Factory Hub: 54.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +19.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 54.1mm (OD: 73.1mm / ID: 54.1mm)
🛒 Order 73.1mm to 54.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 6" ET47
New Wheel Width:7.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET37 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

4x100
2020-2026 FITMENT SPECIFICATION

2026 Hyundai Venue

fitmentspec.com/hyundai/venue/2026
FINAL TORQUE80 ft-lbs(110 Nm)
Bolt Pattern (PCD)4x100
Center Bore54.1 mm
Fastener & ThreadM12 x 1.5Lug Nut • Conical 60 Degree
TPMS CalibrationDirect Tire Pressure SensorDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 4x100 bolt pattern and 54.1 mm hub bore.

✓ No Centering Rings Required
1990-199754.1 mm CB
Mazda MX-5 Miata
Torque: 80 ft-lbsSpecs →
2016-202654.1 mm CB
Mazda MX-5 Miata
Torque: 80 ft-lbsSpecs →
🔄

Cross-Vehicle OEM Wheel Swap Compatibility (4x100)

Verified OEM donor vehicles whose factory wheels fit the Hyundai Venue hub (54.1mm).

Wheel Swap Calculator →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +8.24" (+33.68%)
+33.68%
Original Baseline Tire185/65R15
New Target Tire285/70R17
QUICK SIZES:
24.5"32.7"
Speedometer Variance Table
30 mph gauge40.1 actual+10.1 mph
45 mph gauge60.2 actual+15.2 mph
60 mph gauge80.2 actual+20.2 mph
70 mph gauge93.6 actual+23.6 mph
80 mph gauge106.9 actual+26.9 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
205/70R16
Mounted on 16x6.5" Wheel
PCD: 4x100
Center Bore: 54.1 mm
🛡️ Technical Benefits for 2026 Hyundai Venue
⛷️ Higher Ground Pressure
A narrower tire (205mm vs 185mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TIRE PRESSURE SENSOR TPMS433 MHz
Architecture
Indirect Wheel Speed ABS
Sensor Part Number
52933-C1100
Relearn Protocol
Automatic Drive Relearn
Relearn Sequence0 / 1 Steps Complete
1
Adjust all tires to cold placard pressure (33 PSI). Drive at 16 mph (25 km/h) or faster for 15-20 minutes to allow the TPMS receiver to calibrate.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2026 Venue

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2026 Hyundai Venue)

8 Verified Q&As
Q What is the bolt pattern for a 2026 Hyundai Venue?
The factory bolt pattern (PCD) for the 2026 Hyundai Venue is 4x100 (4-lug configuration) with a pitch circle diameter of 100 mm. Center bore hub diameter is 54.1 mm.
Q What is the wheel lug torque specification for a 2026 Hyundai Venue?
The official factory wheel lug torque specification for the 2026 Hyundai Venue is 80 ft-lbs (110 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2026 Hyundai Venue?
The official maximum braked towing capacity for the 2026 Hyundai Venue is 1,000 lbs (454 kg) with a maximum tongue weight limit of 100 lbs. Recommended hitch receiver: Class I (1.25-inch Receiver). Unbraked trailer limit is 350 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2026 Hyundai Venue?
Factory stock tire sizing for the 2026 Hyundai Venue is 185/65R15 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2026 Hyundai Venue and are hub centric rings needed?
The center bore diameter is exactly 54.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 54.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2026 Hyundai Venue use?
The 2026 Hyundai Venue utilizes M12 x 1.5 Lug Nuts with a Conical 60 Degree seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2026 Hyundai Venue have Direct or Indirect TPMS and how is it reset?
This vehicle utilizes standard valve stems without requiring active electronic TPMS sensor recalibration.
Q What aftermarket wheel offset and tire sizes fit a 2026 Hyundai Venue without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +38mm and +50mm with a flush target of ET +40. Always test clearance at full steering lock.