FitmentSpec Logo
Land Rover logo
L663 (2nd Gen) (2020–2026)

2025 Land Rover Defender

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2025 Land Rover Defender
Factory Powertrain 3.0L i6 Turbocharged MHEV Ingenium / 5.0L Supercharged V8
395 HP (295 kW) 406 lb-ft 3.0L Inline-6 / V8
Chassis Dimensions Exterior & Curb Weight
L: 197.6" W: 78.6" WB: 119" 4,815 - 5,735 lbs lbs
Bolt Pattern5-Lug
5x120
Center BoreHub Centric
72.6 mm
Hub Ring Spigot Diameter
Offset RangeET
+35 to +45
Flush Target: ET +30
Lug TorqueM14 x 1.5
103 ft-lbs
140 Nm • Flat Seat
Fastener: Flat Seat with Captive Washer (OEM) / Conical 60 Degree (Aftermarket) Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2025 Land Rover Defender Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 8,201 lbs
Max Towing (Braked)
8,201 lbs
3,720 kg
With factory trailer brakes
Max Payload Capacity
1,984 lbs
900 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
820 lbs
372 kg
Maximum hitch downward load
Hitch Receiver Class
Class IV (2-inch Receiver)
Weight distribution rated
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2025 Defender
Selected Load: 8,201 lbs • Vehicle Rating: 8,201 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Defender 110 and 130 with inline-6 mild-hybrid or V8 rated up to 8,201 lbs (3,720 kg). Advanced Tow Assist controls trailer reversing automatically.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 1500 lbs (680 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2025 Land Rover Defender Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2025 Land Rover Defender? The factory bolt pattern is 5x120 (5-lug) with a 72.6 mm center bore. The manufacturer specified wheel lug torque is 103 ft-lbs (140 Nm) using M14 x 1.5 Lug Nuts with a Flat Seat with Captive Washer (OEM) / Conical 60 Degree (Aftermarket) seating surface. Safe wheel offset range is +35mm to +45mm.

Factory OEM Wheel & Tire Configurations (2025)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
Defender S / SE (19" Off-Road) 19x8.5 ET+41.5
255/65R19 Compare ⚡
38 PSI Find Tires →
X-Dynamic / V8 (20"-22" All-Terrain) 20x8.5 ET+41.5
255/60R20 Compare ⚡
38 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Land Rover Defender factory 72.6 mm hub snout.

Factory Hub: 72.6mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +0.5 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 72.6mm (OD: 73.1mm / ID: 72.6mm)
🛒 Order 73.1mm to 72.6mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 8.5" ET41.5
New Wheel Width:9.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET31.5 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x120
2020-2026 FITMENT SPECIFICATION

2025 Land Rover Defender

fitmentspec.com/land-rover/defender/2025
FINAL TORQUE103 ft-lbs(140 Nm)
Bolt Pattern (PCD)5x120
Center Bore72.6 mm
Fastener & ThreadM14 x 1.5Lug Nut • Flat Seat with Captive Washer (OEM) / Conical 60 Degree (Aftermarket)
TPMS CalibrationDirect Tire Pressure Monitoring System (TPMS)Door Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x120 bolt pattern and 72.6 mm hub bore.

✓ No Centering Rings Required
2024-202672.56 mm CB
Dodge Charger
Torque: 103 ft-lbsSpecs →
2020-202672.6 mm CB
Land Rover Defender 110
Torque: 103 ft-lbsSpecs →
2017-202672.6 mm CB
Land Rover Discovery
Torque: 103 ft-lbsSpecs →
2022-202672.6 mm CB
Land Rover Range Rover
Torque: 103 ft-lbsSpecs →
2023-202672.6 mm CB
Land Rover Range Rover Sport
Torque: 103 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Within Normal ToleranceDiameter: +0.66" (+2.05%)
+2.05%
Original Baseline Tire255/65R19
New Target Tire285/70R17
QUICK SIZES:
32.1"32.7"
Speedometer Variance Table
30 mph gauge30.6 actual+0.6 mph
45 mph gauge45.9 actual+0.9 mph
60 mph gauge61.2 actual+1.2 mph
70 mph gauge71.4 actual+1.4 mph
80 mph gauge81.6 actual+1.6 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
235/75R17
Mounted on 17x7.5" Wheel
PCD: 5x120
Center Bore: 72.6 mm
🛡️ Technical Benefits for 2025 Land Rover Defender
⛷️ Higher Ground Pressure
A narrower tire (235mm vs 255mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TIRE PRESSURE MONITORING SYSTEM (TPMS) TPMS433 MHz
Architecture
Indirect Wheel Speed ABS
Sensor Part Number
LR070840
Relearn Protocol
Automatic Drive Relearn
Relearn Sequence0 / 1 Steps Complete
1
Adjust tires to door jamb cold placard values (front 38 PSI, rear 42 PSI). Drive the vehicle continuously above 12 mph (20 km/h) for approximately 15 minutes.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2025 Defender

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2025 Land Rover Defender)

8 Verified Q&As
Q What is the bolt pattern for a 2025 Land Rover Defender?
The factory bolt pattern (PCD) for the 2025 Land Rover Defender is 5x120 (5-lug configuration) with a pitch circle diameter of 120 mm. Center bore hub diameter is 72.6 mm.
Q What is the wheel lug torque specification for a 2025 Land Rover Defender?
The official factory wheel lug torque specification for the 2025 Land Rover Defender is 103 ft-lbs (140 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2025 Land Rover Defender?
The official maximum braked towing capacity for the 2025 Land Rover Defender is 8,201 lbs (3,720 kg) with a maximum tongue weight limit of 820 lbs. Recommended hitch receiver: Class IV (2-inch Receiver). Unbraked trailer limit is 1,500 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2025 Land Rover Defender?
Factory stock tire sizing for the 2025 Land Rover Defender is 255/65R19 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2025 Land Rover Defender and are hub centric rings needed?
The center bore diameter is exactly 72.6 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 72.6mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2025 Land Rover Defender use?
The 2025 Land Rover Defender utilizes M14 x 1.5 Lug Nuts with a Flat Seat with Captive Washer (OEM) / Conical 60 Degree (Aftermarket) seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2025 Land Rover Defender have Direct or Indirect TPMS and how is it reset?
This vehicle utilizes standard valve stems without requiring active electronic TPMS sensor recalibration.
Q What aftermarket wheel offset and tire sizes fit a 2025 Land Rover Defender without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +35mm and +45mm with a flush target of ET +30. Always test clearance at full steering lock.