FitmentSpec Logo
McLaren logo
MCLA Carbon Monocoque (Artura Coupe / Spider) (2022–2026)

2024 McLaren Artura

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2024 McLaren Artura
Factory Powertrain 3.0L Twin-Turbo 120° V6 + Axial-Flux E-Motor Hybrid (690 hp / 531 lb-ft)
690 HP
Chassis Dimensions Exterior & Curb Weight
WB: 103.9"
Bolt Pattern5-Lug
5x112
Center BoreHub Centric
57.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+35 to +45
Flush Target: ET +38
Lug TorqueM14 x 1.5
96 ft-lbs
130 Nm • Cone Seat
Fastener: Cone 60° Lug Bolt. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2024 McLaren Artura Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Towing Not Recommended
Max Towing (Braked)
0 lbs
Not Certified
Factory sports chassis
Max Payload Capacity
550 lbs
249 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
0 lbs
0 kg
Maximum hitch downward load
Hitch Receiver Class
Not Recommended for Towing
Standard bumper / ball mount
📋 Factory Towing Guidance:

Manufacturer does not certify or recommend this performance chassis for trailer towing. Hitch installation is unsupported and may void warranty.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 0 lbs (0 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2024 McLaren Artura Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2024 McLaren Artura? The factory bolt pattern is 5x112 (5-lug) with a 57.1 mm center bore. The manufacturer specified wheel lug torque is 96 ft-lbs (130 Nm) using M14 x 1.5 Lug Bolts with a Cone 60° seating surface. Safe wheel offset range is +35mm to +45mm.

Factory OEM Wheel & Tire Configurations (2024)

1 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
Artura (19"/20" Dynamo 10-Spoke Forged Alloy) 19x8 ET+42
235/35ZR19 (Pirelli P Zero Cyber Tire MC) Compare ⚡
32 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for McLaren Artura factory 57.1 mm hub snout.

Factory Hub: 57.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +16.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 57.1mm (OD: 73.1mm / ID: 57.1mm)
🛒 Order 73.1mm to 57.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 8" ET42
New Wheel Width:9.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET32 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x112
2022-2026 FITMENT SPECIFICATION

2024 McLaren Artura

fitmentspec.com/mclaren/artura/2024
FINAL TORQUE96 ft-lbs(130 Nm)
Bolt Pattern (PCD)5x112
Center Bore57.1 mm
Fastener & ThreadM14 x 1.5Lug Bolt • Cone 60°
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x112 bolt pattern and 57.1 mm hub bore.

✓ No Centering Rings Required
2022-202657.1 mm CB
Audi A3
Torque: 96 ft-lbsSpecs →
2017-202357.1 mm CB
Audi R8
Torque: 96 ft-lbsSpecs →
2022-202657.1 mm CB
Audi RS3
Torque: 96 ft-lbsSpecs →
2012-202257.1 mm CB
Lamborghini Aventador
Torque: 96 ft-lbsSpecs →
2004-201457.1 mm CB
Lamborghini Gallardo
Torque: 96 ft-lbsSpecs →
2015-202457.1 mm CB
Lamborghini Huracan
Torque: 96 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +7.23" (+28.39%)
+28.39%
Original Baseline Tire235/35R19
New Target Tire285/70R17
QUICK SIZES:
25.5"32.7"
Speedometer Variance Table
30 mph gauge38.5 actual+8.5 mph
45 mph gauge57.8 actual+12.8 mph
60 mph gauge77.0 actual+17.0 mph
70 mph gauge89.9 actual+19.9 mph
80 mph gauge102.7 actual+22.7 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
215/55R17
Mounted on 17x7.0" Wheel
PCD: 5x112
Center Bore: 57.1 mm
🛡️ Technical Benefits for 2024 McLaren Artura
⛷️ Higher Ground Pressure
A narrower tire (215mm vs 235mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Auto-Relearn Drive Cycle
Relearn Sequence0 / 1 Steps Complete
1
Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2024 Artura

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2024 McLaren Artura)

8 Verified Q&As
Q What is the bolt pattern for a 2024 McLaren Artura?
The factory bolt pattern (PCD) for the 2024 McLaren Artura is 5x112 (5-lug configuration) with a pitch circle diameter of 112 mm. Center bore hub diameter is 57.1 mm.
Q What is the wheel lug torque specification for a 2024 McLaren Artura?
The official factory wheel lug torque specification for the 2024 McLaren Artura is 96 ft-lbs (130 Nm). Tighten all Lug Bolts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2024 McLaren Artura?
The manufacturer does not rate or recommend the 2024 McLaren Artura for trailer towing. Installing an aftermarket trailer hitch receiver is not advised for towing loads and may void powertrain warranty.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2024 McLaren Artura?
Factory stock tire sizing for the 2024 McLaren Artura is 235/35ZR19 (Pirelli P Zero Cyber Tire MC) with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2024 McLaren Artura and are hub centric rings needed?
The center bore diameter is exactly 57.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 57.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2024 McLaren Artura use?
The 2024 McLaren Artura utilizes M14 x 1.5 Lug Bolts with a Cone 60° seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2024 McLaren Artura have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn Drive Cycle: Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
Q What aftermarket wheel offset and tire sizes fit a 2024 McLaren Artura without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +35mm and +45mm with a flush target of ET +38. Always test clearance at full steering lock.