FitmentSpec Logo
Mitsubishi logo
4th Gen V80/V90 (GLS / Exceed / Super Exceed 3.2L DI-D / 3.8L V6) (2007–2021)

2018 Mitsubishi Pajero

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2018 Mitsubishi Pajero
OEM Powertrain Standard Specification
Chassis Dimensions Exterior & Curb Weight
Center BoreHub Centric
67.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+35 to +46
Flush Target: ET +38
Lug TorqueM12 x 1.5
94 ft-lbs
127 Nm • Mag Seat
Fastener: Mag Seat with Flat Washer Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2018 Mitsubishi Pajero Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 1,000 lbs
Max Towing (Braked)
1,000 lbs
454 kg
With factory trailer brakes
Max Payload Capacity
850 lbs
386 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
100 lbs
45 kg
Maximum hitch downward load
Hitch Receiver Class
Class I (1.25-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2018 Pajero
Selected Load: 1,000 lbs • Vehicle Rating: 1,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Light duty towing up to 1,000 lbs. Recommended primarily for hitch-mounted accessories (bike racks, ski racks, cargo baskets).

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 350 lbs (159 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2018 Mitsubishi Pajero Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2018 Mitsubishi Pajero? The factory bolt pattern is 6x139.7 (6-lug) with a 67.1 mm center bore. The manufacturer specified wheel lug torque is 94 ft-lbs (127 Nm) using M12 x 1.5 Lug Nuts with a Mag Seat with Flat Washer seating surface. Safe wheel offset range is +35mm to +46mm.

Factory OEM Wheel & Tire Configurations (2018)

1 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
Super Exceed (18" 6-Spoke High Gloss Alloy Wheels) 18x7.5 ET+46
265/60R18 Compare ⚡
32 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Mitsubishi Pajero factory 67.1 mm hub snout.

Factory Hub: 67.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +6.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 67.1mm (OD: 73.1mm / ID: 67.1mm)
🛒 Order 73.1mm to 67.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 7.5" ET46
New Wheel Width:8.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET36 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

6x139.7
2007-2021 FITMENT SPECIFICATION

2018 Mitsubishi Pajero

fitmentspec.com/mitsubishi/pajero/2018
FINAL TORQUE94 ft-lbs(127 Nm)
Bolt Pattern (PCD)6x139.7
Center Bore67.1 mm
Fastener & ThreadM12 x 1.5Lug Nut • Mag Seat with Flat Washer
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +2.19" (+7.17%)
+7.17%
Original Baseline Tire265/60R18
New Target Tire285/70R17
QUICK SIZES:
30.5"32.7"
Speedometer Variance Table
30 mph gauge32.2 actual+2.2 mph
45 mph gauge48.2 actual+3.2 mph
60 mph gauge64.3 actual+4.3 mph
70 mph gauge75.0 actual+5.0 mph
80 mph gauge85.7 actual+5.7 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
255/65R17
Mounted on 17x6.5" Wheel
PCD: 6x139.7
Center Bore: 67.1 mm
🛡️ Technical Benefits for 2018 Mitsubishi Pajero
⛷️ Higher Ground Pressure
A narrower tire (255mm vs 265mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Auto-Relearn Drive Cycle
Relearn Sequence0 / 1 Steps Complete
1
Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2018 Pajero

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2018 Mitsubishi Pajero)

8 Verified Q&As
Q What is the bolt pattern for a 2018 Mitsubishi Pajero?
The factory bolt pattern (PCD) for the 2018 Mitsubishi Pajero is 6x139.7 (6-lug configuration) with a pitch circle diameter of 139.7 mm. Center bore hub diameter is 67.1 mm.
Q What is the wheel lug torque specification for a 2018 Mitsubishi Pajero?
The official factory wheel lug torque specification for the 2018 Mitsubishi Pajero is 94 ft-lbs (127 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2018 Mitsubishi Pajero?
The official maximum braked towing capacity for the 2018 Mitsubishi Pajero is 1,000 lbs (454 kg) with a maximum tongue weight limit of 100 lbs. Recommended hitch receiver: Class I (1.25-inch Receiver). Unbraked trailer limit is 350 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2018 Mitsubishi Pajero?
Factory stock tire sizing for the 2018 Mitsubishi Pajero is 265/60R18 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2018 Mitsubishi Pajero and are hub centric rings needed?
The center bore diameter is exactly 67.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 67.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2018 Mitsubishi Pajero use?
The 2018 Mitsubishi Pajero utilizes M12 x 1.5 Lug Nuts with a Mag Seat with Flat Washer seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2018 Mitsubishi Pajero have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn Drive Cycle: Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
Q What aftermarket wheel offset and tire sizes fit a 2018 Mitsubishi Pajero without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +35mm and +46mm with a flush target of ET +38. Always test clearance at full steering lock.