FitmentSpec Logo
Nissan logo
CBA / DBA / 4BA (R35 Premium / Track Edition / NISMO) (2009–2026)

2024 Nissan GT-R

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2024 Nissan GT-R
Factory Powertrain 3.8L Twin-Turbo VR38DETT Hand-Built V6 (NISMO: 600 hp / 481 lb-ft)
600 HP
Chassis Dimensions Exterior & Curb Weight
WB: 109.4"
Center BoreHub Centric
66.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+20 to +45
Flush Target: ET +25
Lug TorqueM12 x 1.25
97 ft-lbs
132 Nm • Cone Seat
Fastener: Cone 60° with Knurled Bead Grip Wheels Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2024 Nissan GT-R Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Towing Not Recommended
Max Towing (Braked)
0 lbs
Not Certified
Factory sports chassis
Max Payload Capacity
550 lbs
249 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
0 lbs
0 kg
Maximum hitch downward load
Hitch Receiver Class
Not Recommended for Towing
Standard bumper / ball mount
📋 Factory Towing Guidance:

Manufacturer does not certify or recommend this performance chassis for trailer towing. Hitch installation is unsupported and may void warranty.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 0 lbs (0 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2024 Nissan GT-R Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2024 Nissan GT-R? The factory bolt pattern is 5x114.3 (5-lug) with a 66.1 mm center bore. The manufacturer specified wheel lug torque is 97 ft-lbs (132 Nm) using M12 x 1.25 Lug Nuts with a Cone 60° with Knurled Bead Grip Wheels seating surface. Safe wheel offset range is +20mm to +45mm.

Factory OEM Wheel & Tire Configurations (2024)

1 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
GT-R NISMO (20" RAYS Forged Lightweight Wheels with Knurling) 20x10 ET+41
255/40ZRF20 (Dunlop SP Sport Maxx GT600 DSST CTT) Compare ⚡
30 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Nissan GT-R factory 66.1 mm hub snout.

Factory Hub: 66.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +7.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 66.1mm (OD: 73.1mm / ID: 66.1mm)
🛒 Order 73.1mm to 66.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 10" ET41
New Wheel Width:11.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET31 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x114.3
2009-2026 FITMENT SPECIFICATION

2024 Nissan GT-R

fitmentspec.com/nissan/gt-r/2024
FINAL TORQUE97 ft-lbs(132 Nm)
Bolt Pattern (PCD)5x114.3
Center Bore66.1 mm
Fastener & ThreadM12 x 1.25Lug Nut • Cone 60° with Knurled Bead Grip Wheels
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x114.3 bolt pattern and 66.1 mm hub bore.

✓ No Centering Rings Required
2008-201366.1 mm CB
Infiniti G37
Torque: 97 ft-lbsSpecs →
2014-202666.1 mm CB
Infiniti Q50
Torque: 97 ft-lbsSpecs →
2014-202666.1 mm CB
Infiniti Q50
Torque: 97 ft-lbsSpecs →
2017-202266.1 mm CB
Infiniti Q60
Torque: 97 ft-lbsSpecs →
2022-202666.1 mm CB
Infiniti QX60
Torque: 97 ft-lbsSpecs →
2003-200866.1 mm CB
Nissan 350Z
Torque: 97 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Significant DifferenceDiameter: +1.10" (+3.49%)
+3.49%
Original Baseline Tire265/70R17
New Target Tire285/70R17
QUICK SIZES:
31.6"32.7"
Speedometer Variance Table
30 mph gauge31.0 actual+1.0 mph
45 mph gauge46.6 actual+1.6 mph
60 mph gauge62.1 actual+2.1 mph
70 mph gauge72.4 actual+2.4 mph
80 mph gauge82.8 actual+2.8 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
215/55R18
Mounted on 18x9.0" Wheel
PCD: 5x114.3
Center Bore: 66.1 mm
🛡️ Technical Benefits for 2024 Nissan GT-R
⛷️ Higher Ground Pressure
A narrower tire (215mm vs 235mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Auto-Relearn Drive Cycle
Relearn Sequence0 / 1 Steps Complete
1
Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2024 GT-R

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2024 Nissan GT-R)

8 Verified Q&As
Q What is the bolt pattern for a 2024 Nissan GT-R?
The factory bolt pattern (PCD) for the 2024 Nissan GT-R is 5x114.3 (5-lug configuration) with a pitch circle diameter of 114.3 mm. Center bore hub diameter is 66.1 mm.
Q What is the wheel lug torque specification for a 2024 Nissan GT-R?
The official factory wheel lug torque specification for the 2024 Nissan GT-R is 97 ft-lbs (132 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2024 Nissan GT-R?
The manufacturer does not rate or recommend the 2024 Nissan GT-R for trailer towing. Installing an aftermarket trailer hitch receiver is not advised for towing loads and may void powertrain warranty.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2024 Nissan GT-R?
Factory stock tire sizing for the 2024 Nissan GT-R is 255/40ZRF20 (Dunlop SP Sport Maxx GT600 DSST CTT) with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2024 Nissan GT-R and are hub centric rings needed?
The center bore diameter is exactly 66.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 66.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2024 Nissan GT-R use?
The 2024 Nissan GT-R utilizes M12 x 1.25 Lug Nuts with a Cone 60° with Knurled Bead Grip Wheels seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2024 Nissan GT-R have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn Drive Cycle: Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
Q What aftermarket wheel offset and tire sizes fit a 2024 Nissan GT-R without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +20mm and +45mm with a flush target of ET +25. Always test clearance at full steering lock.