FitmentSpec Logo
Polestar logo
1st Gen CMA (Long Range Dual Motor Performance Pack AWD) (2021–2026)

2025 Polestar 2

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2025 Polestar 2
OEM Powertrain Standard Specification
Chassis Dimensions Exterior & Curb Weight
Bolt Pattern5-Lug
5x108
Center BoreHub Centric
63.4 mm
Hub Ring Spigot Diameter
Offset RangeET
+45 to +55
Flush Target: ET +50
Lug TorqueM14 x 1.5
103 ft-lbs
140 Nm • Conical Seat
Fastener: Conical Seat 60 Degree Lug Bolt. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2025 Polestar 2 Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 1,000 lbs
Max Towing (Braked)
1,000 lbs
454 kg
With factory trailer brakes
Max Payload Capacity
850 lbs
386 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
100 lbs
45 kg
Maximum hitch downward load
Hitch Receiver Class
Class I (1.25-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2025 2
Selected Load: 1,000 lbs • Vehicle Rating: 1,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Light duty towing up to 1,000 lbs. Recommended primarily for hitch-mounted accessories (bike racks, ski racks, cargo baskets).

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 350 lbs (159 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2025 Polestar 2 Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2025 Polestar 2? The factory bolt pattern is 5x108 (5-lug) with a 63.4 mm center bore. The manufacturer specified wheel lug torque is 103 ft-lbs (140 Nm) using M14 x 1.5 Lug Bolts with a Conical Seat 60 Degree seating surface. Safe wheel offset range is +45mm to +55mm.

Factory OEM Wheel & Tire Configurations (2025)

1 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
Performance Pack (20" 4-Y Spoke Black Polished Forged Alloy) 20x8 ET+50
245/40R20 Compare ⚡
32-35 PSI Placard Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Polestar 2 factory 63.4 mm hub snout.

Factory Hub: 63.4mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +9.7 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 63.4mm (OD: 73.1mm / ID: 63.4mm)
🛒 Order 73.1mm to 63.4mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 8" ET50
New Wheel Width:9.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET40 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x108
2021-2026 FITMENT SPECIFICATION

2025 Polestar 2

fitmentspec.com/polestar/2/2025
FINAL TORQUE103 ft-lbs(140 Nm)
Bolt Pattern (PCD)5x108
Center Bore63.4 mm
Fastener & ThreadM14 x 1.5Lug Bolt • Conical Seat 60 Degree
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x108 bolt pattern and 63.4 mm hub bore.

✓ No Centering Rings Required
2021-202663.4 mm CB
Ford Bronco Sport
Torque: 103 ft-lbsSpecs →
2019-202463.4 mm CB
Ford Edge
Torque: 103 ft-lbsSpecs →
2020-202663.4 mm CB
Ford Escape
Torque: 103 ft-lbsSpecs →
2016-201863.4 mm CB
Ford Focus RS
Torque: 103 ft-lbsSpecs →
2013-202063.4 mm CB
Ford Fusion
Torque: 103 ft-lbsSpecs →
2022-202663.4 mm CB
Ford Maverick
Torque: 103 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +4.99" (+18.01%)
+18.01%
Original Baseline Tire245/40R20
New Target Tire285/70R17
QUICK SIZES:
27.7"32.7"
Speedometer Variance Table
30 mph gauge35.4 actual+5.4 mph
45 mph gauge53.1 actual+8.1 mph
60 mph gauge70.8 actual+10.8 mph
70 mph gauge82.6 actual+12.6 mph
80 mph gauge94.4 actual+14.4 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
225/50R18
Mounted on 18x7.0" Wheel
PCD: 5x108
Center Bore: 63.4 mm
🛡️ Technical Benefits for 2025 Polestar 2
⛷️ Higher Ground Pressure
A narrower tire (225mm vs 245mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Auto-Relearn Drive Cycle
Relearn Sequence0 / 1 Steps Complete
1
Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2025 2

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2025 Polestar 2)

8 Verified Q&As
Q What is the bolt pattern for a 2025 Polestar 2?
The factory bolt pattern (PCD) for the 2025 Polestar 2 is 5x108 (5-lug configuration) with a pitch circle diameter of 108 mm. Center bore hub diameter is 63.4 mm.
Q What is the wheel lug torque specification for a 2025 Polestar 2?
The official factory wheel lug torque specification for the 2025 Polestar 2 is 103 ft-lbs (140 Nm). Tighten all Lug Bolts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2025 Polestar 2?
The official maximum braked towing capacity for the 2025 Polestar 2 is 1,000 lbs (454 kg) with a maximum tongue weight limit of 100 lbs. Recommended hitch receiver: Class I (1.25-inch Receiver). Unbraked trailer limit is 350 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2025 Polestar 2?
Factory stock tire sizing for the 2025 Polestar 2 is 245/40R20 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2025 Polestar 2 and are hub centric rings needed?
The center bore diameter is exactly 63.4 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 63.4mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2025 Polestar 2 use?
The 2025 Polestar 2 utilizes M14 x 1.5 Lug Bolts with a Conical Seat 60 Degree seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2025 Polestar 2 have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn Drive Cycle: Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
Q What aftermarket wheel offset and tire sizes fit a 2025 Polestar 2 without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +45mm and +55mm with a flush target of ET +50. Always test clearance at full steering lock.