FitmentSpec Logo
Ram logo
5th Gen HD (2019–2026)

2019 Ram 2500 Heavy Duty

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2019 Ram 2500 Heavy Duty
Factory Powertrain 6.7L Cummins Turbo Diesel I6 / 6.4L HEMI V8
410 HP (306 kW) 850 lb-ft 6.7L Inline-6 Diesel / V8 Gas
Chassis Dimensions Exterior & Curb Weight
L: 238.8" W: 83.5" WB: 149.5" 6,432 - 7,420 lbs lbs
Center BoreHub Centric
121.3 mm
Hub Ring Spigot Diameter
Offset RangeET
+18 to +45
Flush Target: ET +18
Lug TorqueM14 x 1.5
140 ft-lbs
190 Nm • Conical Seat
Fastener: Conical 60 Degree Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2019 Ram 2500 Heavy Duty Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 1,000 lbs
Max Towing (Braked)
1,000 lbs
454 kg
With factory trailer brakes
Max Payload Capacity
850 lbs
386 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
100 lbs
45 kg
Maximum hitch downward load
Hitch Receiver Class
Class I (1.25-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2019 2500 Heavy Duty
Selected Load: 1,000 lbs • Vehicle Rating: 1,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Light duty towing up to 1,000 lbs. Recommended primarily for hitch-mounted accessories (bike racks, ski racks, cargo baskets).

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 350 lbs (159 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2019 Ram 2500 Heavy Duty Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2019 Ram 2500 Heavy Duty? The factory bolt pattern is 8x165.1 (8-lug) with a 121.3 mm center bore. The manufacturer specified wheel lug torque is 140 ft-lbs (190 Nm) using M14 x 1.5 Lug Nuts with a Conical 60 Degree seating surface. Safe wheel offset range is +18mm to +45mm.

Factory OEM Wheel & Tire Configurations (2019)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
Tradesman / Big Horn / Laramie (18" HD) 18x8 ET+43.4
LT275/70R18E Compare ⚡
60 PSI Find Tires →
Power Wagon / Rebel (17"-20" 33" All-Terrain) 17x8 ET+43.4
LT285/70R17D (33" Goodyear DuraTrac) Compare ⚡
60 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Ram 2500 Heavy Duty factory 121.3 mm hub snout.

Factory Hub: 121.3mm
Hub Diagnostic Result
🚨 INCOMPATIBLE WHEEL BORE (TOO SMALL)

The wheel bore (73.1 mm) is smaller than the car hub (121.3 mm). The wheel will NOT physically seat flush on the hub face without wheel spacers or center-bore machining.

💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 8" ET43.4
New Wheel Width:9.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET33.4 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

8x165.1
2019-2026 FITMENT SPECIFICATION

2019 Ram 2500 Heavy Duty

fitmentspec.com/ram/2500/2019
FINAL TORQUE140 ft-lbs(190 Nm)
Bolt Pattern (PCD)8x165.1
Center Bore121.3 mm
Fastener & ThreadM14 x 1.5Lug Nut • Conical 60 Degree
TPMS CalibrationDirect Heavy-Duty Tire Pressure Monitoring (8-Lug 8x6.5)Door Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 8x165.1 bolt pattern and 121.3 mm hub bore.

✓ No Centering Rings Required
2019-2026121.3 mm CB
Ram 3500
Torque: 140 ft-lbsSpecs →
🔄

Cross-Vehicle OEM Wheel Swap Compatibility (8x165.1)

Verified OEM donor vehicles whose factory wheels fit the Ram 2500 Heavy Duty hub (121.3mm).

Wheel Swap Calculator →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Within Normal ToleranceDiameter: -0.45" (-1.35%)
-1.35%
Original Baseline Tire275/70R18
New Target Tire285/70R17
QUICK SIZES:
33.2"32.7"
Speedometer Variance Table
30 mph gauge29.6 actual-0.4 mph
45 mph gauge44.4 actual-0.6 mph
60 mph gauge59.2 actual-0.8 mph
70 mph gauge69.1 actual-0.9 mph
80 mph gauge78.9 actual-1.1 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
265/75R17
Mounted on 17x7.0" Wheel
PCD: 8x165.1
Center Bore: 121.3 mm
🛡️ Technical Benefits for 2019 Ram 2500 Heavy Duty
⛷️ Higher Ground Pressure
A narrower tire (265mm vs 275mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT HEAVY-DUTY TIRE PRESSURE MONITORING (8-LUG 8X6.5) TPMS433 MHz
Architecture
Indirect Wheel Speed ABS
Sensor Part Number
68313387AB
Relearn Protocol
Drive Relearn
Relearn Sequence0 / 1 Steps Complete
1
Ensure 60 PSI front / 65 PSI rear cold pressures. Drive continuously above 15 mph for 15 to 20 minutes.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2019 2500 Heavy Duty

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2019 Ram 2500 Heavy Duty)

8 Verified Q&As
Q What is the bolt pattern for a 2019 Ram 2500 Heavy Duty?
The factory bolt pattern (PCD) for the 2019 Ram 2500 Heavy Duty is 8x165.1 (8-lug configuration) with a pitch circle diameter of 165.1 mm. Center bore hub diameter is 121.3 mm.
Q What is the wheel lug torque specification for a 2019 Ram 2500 Heavy Duty?
The official factory wheel lug torque specification for the 2019 Ram 2500 Heavy Duty is 140 ft-lbs (190 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2019 Ram 2500 Heavy Duty?
The official maximum braked towing capacity for the 2019 Ram 2500 Heavy Duty is 1,000 lbs (454 kg) with a maximum tongue weight limit of 100 lbs. Recommended hitch receiver: Class I (1.25-inch Receiver). Unbraked trailer limit is 350 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2019 Ram 2500 Heavy Duty?
Factory stock tire sizing for the 2019 Ram 2500 Heavy Duty is LT275/70R18E with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2019 Ram 2500 Heavy Duty and are hub centric rings needed?
The center bore diameter is exactly 121.3 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 121.3mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2019 Ram 2500 Heavy Duty use?
The 2019 Ram 2500 Heavy Duty utilizes M14 x 1.5 Lug Nuts with a Conical 60 Degree seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2019 Ram 2500 Heavy Duty have Direct or Indirect TPMS and how is it reset?
This vehicle utilizes standard valve stems without requiring active electronic TPMS sensor recalibration.
Q What aftermarket wheel offset and tire sizes fit a 2019 Ram 2500 Heavy Duty without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +18mm and +45mm with a flush target of ET +18. Always test clearance at full steering lock.