FitmentSpec Logo
Rivian logo
Gen 1 & Gen 2 (Adventure / Dual-Motor / Tri-Motor / Quad-Motor) (2022–2026)

2025 Rivian R1T

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2025 Rivian R1T
Factory Powertrain Quad-Motor AWD System with Independent Wheel Torque Vectoring (835 hp - 1025 hp total)
835 HP
Chassis Dimensions Exterior & Curb Weight
WB: 135.8"
Center BoreHub Centric
64.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+42 to +52
Flush Target: ET +48
Lug TorqueM14 x 1.5
140 ft-lbs
190 Nm • Cone Seat
Fastener: Cone 60° Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2025 Rivian R1T Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 11,000 lbs
Max Towing (Braked)
11,000 lbs
4,990 kg
With factory trailer brakes
Max Payload Capacity
1,764 lbs
800 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
1,100 lbs
499 kg
Maximum hitch downward load
Hitch Receiver Class
Class IV (Integrated 2-inch Receiver)
Weight distribution rated
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2025 R1T
Selected Load: 11,000 lbs • Vehicle Rating: 11,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Quad-Motor and Tri-Motor configurations certified for 11,000 lbs. Automatic trailer detection adjusts regenerative braking and rear ride height.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 1500 lbs (680 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2025 Rivian R1T Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2025 Rivian R1T? The factory bolt pattern is 5x139.7 (5-lug) with a 64.1 mm center bore. The manufacturer specified wheel lug torque is 140 ft-lbs (190 Nm) using M14 x 1.5 Lug Nuts with a Cone 60° seating surface. Safe wheel offset range is +42mm to +52mm.

Factory OEM Wheel & Tire Configurations (2025)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
R1T All-Terrain (20" Forged Alloy Wheels with Pirelli Scorpion A/T) 20x8.5 ET+48
275/65R20 (Pirelli Scorpion All-Terrain Plus) Compare ⚡
48 PSI Find Tires →
R1T Sport (22" Sport Dark Forged Wheels) 22x8.5 ET+48
275/50R22 (Pirelli Scorpion Zero All Season) Compare ⚡
48 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Rivian R1T factory 64.1 mm hub snout.

Factory Hub: 64.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +9.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 64.1mm (OD: 73.1mm / ID: 64.1mm)
🛒 Order 73.1mm to 64.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 8.5" ET48
New Wheel Width:9.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET38 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x139.7
2022-2026 FITMENT SPECIFICATION

2025 Rivian R1T

fitmentspec.com/rivian/r1t/2025
FINAL TORQUE140 ft-lbs(190 Nm)
Bolt Pattern (PCD)5x139.7
Center Bore64.1 mm
Fastener & ThreadM14 x 1.5Lug Nut • Cone 60°
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x139.7 bolt pattern and 64.1 mm hub bore.

✓ No Centering Rings Required
2022-202664.1 mm CB
Rivian R1S
Torque: 140 ft-lbsSpecs →
2022-202664.1 mm CB
Rivian R1S
Torque: 140 ft-lbsSpecs →
🔄

Cross-Vehicle OEM Wheel Swap Compatibility (5x139.7)

Verified OEM donor vehicles whose factory wheels fit the Rivian R1T hub (64.1mm).

Wheel Swap Calculator →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Significant DifferenceDiameter: -1.37" (-4.01%)
-4.01%
Original Baseline Tire275/65R20
New Target Tire285/70R17
QUICK SIZES:
34.1"32.7"
Speedometer Variance Table
30 mph gauge28.8 actual-1.2 mph
45 mph gauge43.2 actual-1.8 mph
60 mph gauge57.6 actual-2.4 mph
70 mph gauge67.2 actual-2.8 mph
80 mph gauge76.8 actual-3.2 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
255/75R18
Mounted on 18x7.5" Wheel
PCD: 5x139.7
Center Bore: 64.1 mm
🛡️ Technical Benefits for 2025 Rivian R1T
⛷️ Higher Ground Pressure
A narrower tire (255mm vs 275mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Auto-Relearn Drive Cycle
Relearn Sequence0 / 1 Steps Complete
1
Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2025 R1T

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2025 Rivian R1T)

8 Verified Q&As
Q What is the bolt pattern for a 2025 Rivian R1T?
The factory bolt pattern (PCD) for the 2025 Rivian R1T is 5x139.7 (5-lug configuration) with a pitch circle diameter of 139.7 mm. Center bore hub diameter is 64.1 mm.
Q What is the wheel lug torque specification for a 2025 Rivian R1T?
The official factory wheel lug torque specification for the 2025 Rivian R1T is 140 ft-lbs (190 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2025 Rivian R1T?
The official maximum braked towing capacity for the 2025 Rivian R1T is 11,000 lbs (4,990 kg) with a maximum tongue weight limit of 1,100 lbs. Recommended hitch receiver: Class IV (Integrated 2-inch Receiver). Unbraked trailer limit is 1,500 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2025 Rivian R1T?
Factory stock tire sizing for the 2025 Rivian R1T is 275/65R20 (Pirelli Scorpion All-Terrain Plus) with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2025 Rivian R1T and are hub centric rings needed?
The center bore diameter is exactly 64.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 64.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2025 Rivian R1T use?
The 2025 Rivian R1T utilizes M14 x 1.5 Lug Nuts with a Cone 60° seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2025 Rivian R1T have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn Drive Cycle: Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
Q What aftermarket wheel offset and tire sizes fit a 2025 Rivian R1T without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +42mm and +52mm with a flush target of ET +48. Always test clearance at full steering lock.