FitmentSpec Logo
Toyota logo
5th Gen A90/A91 (3.0L Turbo B58 382 HP Adaptive Variable Suspension) (2020–2026)

2026 Toyota GR Supra

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2026 Toyota GR Supra
OEM Powertrain Standard Specification
Chassis Dimensions Exterior & Curb Weight
Bolt Pattern5-Lug
5x112
Center BoreHub Centric
66.5 mm
Hub Ring Spigot Diameter
Offset RangeET
+25 to +42
Flush Target: ET +32
Lug TorqueM14 x 1.25
103 ft-lbs
140 Nm • Conical Seat
Fastener: Conical Seat 60 Degree Lug Bolt. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2026 Toyota GR Supra Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Towing Not Recommended
Max Towing (Braked)
0 lbs
Not Certified
Factory sports chassis
Max Payload Capacity
550 lbs
249 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
0 lbs
0 kg
Maximum hitch downward load
Hitch Receiver Class
Not Recommended for Towing
Standard bumper / ball mount
📋 Factory Towing Guidance:

Manufacturer does not certify or recommend this performance chassis for trailer towing. Hitch installation is unsupported and may void warranty.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 0 lbs (0 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2026 Toyota GR Supra Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2026 Toyota GR Supra? The factory bolt pattern is 5x112 (5-lug) with a 66.5 mm center bore. The manufacturer specified wheel lug torque is 103 ft-lbs (140 Nm) using M14 x 1.25 Lug Bolts with a Conical Seat 60 Degree seating surface. Safe wheel offset range is +25mm to +42mm.

Factory OEM Wheel & Tire Configurations (2026)

1 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
3.0 Premium (19" Forged Dual-Tone Aluminum) 19x9 ET+32
255/35ZR19 Compare ⚡
32-35 PSI Placard Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Toyota GR Supra factory 66.5 mm hub snout.

Factory Hub: 66.5mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +6.6 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 66.5mm (OD: 73.1mm / ID: 66.5mm)
🛒 Order 73.1mm to 66.5mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 9" ET32
New Wheel Width:10.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET22 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x112
2020-2026 FITMENT SPECIFICATION

2026 Toyota GR Supra

fitmentspec.com/toyota/gr-supra/2026
FINAL TORQUE103 ft-lbs(140 Nm)
Bolt Pattern (PCD)5x112
Center Bore66.5 mm
Fastener & ThreadM14 x 1.25Lug Bolt • Conical Seat 60 Degree
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x112 bolt pattern and 66.5 mm hub bore.

✓ No Centering Rings Required
2020-202466.5 mm CB
Audi A4
Torque: 103 ft-lbsSpecs →
2018-202666.5 mm CB
Audi A5
Torque: 103 ft-lbsSpecs →
2019-202666.5 mm CB
Audi A6
Torque: 103 ft-lbsSpecs →
2021-202666.5 mm CB
Audi Q5
Torque: 103 ft-lbsSpecs →
2017-202666.5 mm CB
Audi Q7
Torque: 103 ft-lbsSpecs →
2021-202666.5 mm CB
Audi RS6 Avant
Torque: 103 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +6.68" (+25.67%)
+25.67%
Original Baseline Tire255/35R19
New Target Tire285/70R17
QUICK SIZES:
26.0"32.7"
Speedometer Variance Table
30 mph gauge37.7 actual+7.7 mph
45 mph gauge56.6 actual+11.6 mph
60 mph gauge75.4 actual+15.4 mph
70 mph gauge88.0 actual+18.0 mph
80 mph gauge100.5 actual+20.5 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
215/55R17
Mounted on 17x8.0" Wheel
PCD: 5x112
Center Bore: 66.5 mm
🛡️ Technical Benefits for 2026 Toyota GR Supra
⛷️ Higher Ground Pressure
A narrower tire (215mm vs 235mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Auto-Relearn Drive Cycle
Relearn Sequence0 / 1 Steps Complete
1
Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2026 GR Supra

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2026 Toyota GR Supra)

8 Verified Q&As
Q What is the bolt pattern for a 2026 Toyota GR Supra?
The factory bolt pattern (PCD) for the 2026 Toyota GR Supra is 5x112 (5-lug configuration) with a pitch circle diameter of 112 mm. Center bore hub diameter is 66.5 mm.
Q What is the wheel lug torque specification for a 2026 Toyota GR Supra?
The official factory wheel lug torque specification for the 2026 Toyota GR Supra is 103 ft-lbs (140 Nm). Tighten all Lug Bolts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2026 Toyota GR Supra?
The manufacturer does not rate or recommend the 2026 Toyota GR Supra for trailer towing. Installing an aftermarket trailer hitch receiver is not advised for towing loads and may void powertrain warranty.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2026 Toyota GR Supra?
Factory stock tire sizing for the 2026 Toyota GR Supra is 255/35ZR19 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2026 Toyota GR Supra and are hub centric rings needed?
The center bore diameter is exactly 66.5 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 66.5mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2026 Toyota GR Supra use?
The 2026 Toyota GR Supra utilizes M14 x 1.25 Lug Bolts with a Conical Seat 60 Degree seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2026 Toyota GR Supra have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn Drive Cycle: Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
Q What aftermarket wheel offset and tire sizes fit a 2026 Toyota GR Supra without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +25mm and +42mm with a flush target of ET +32. Always test clearance at full steering lock.