FitmentSpec Logo
Toyota logo
ZN8 (2nd Gen) (2022–2026)

2023 Toyota GR86

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2023 Toyota GR86
Factory Powertrain 2.4L FA24D Naturally Aspirated Boxer-4 with D-4S Dual Injection
228 HP (170 kW) 184 lb-ft 2.4L Flat-4
Chassis Dimensions Exterior & Curb Weight
L: 167.9" W: 69.9" WB: 101.4" 2,811 - 2,851 lbs lbs
Bolt Pattern5-Lug
5x100
Center BoreHub Centric
56.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+35 to +48
Flush Target: ET +38
Lug TorqueM12 x 1.25
89 ft-lbs
120 Nm • Conical Seat
Fastener: Conical 60 Degree Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2023 Toyota GR86 Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Towing Not Recommended
Max Towing (Braked)
0 lbs
Not Certified
Factory sports chassis
Max Payload Capacity
550 lbs
249 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
0 lbs
0 kg
Maximum hitch downward load
Hitch Receiver Class
Not Recommended for Towing
Standard bumper / ball mount
📋 Factory Towing Guidance:

Manufacturer does not certify or recommend this performance chassis for trailer towing. Hitch installation is unsupported and may void warranty.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 0 lbs (0 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2023 Toyota GR86 Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2023 Toyota GR86? The factory bolt pattern is 5x100 (5-lug) with a 56.1 mm center bore. The manufacturer specified wheel lug torque is 89 ft-lbs (120 Nm) using M12 x 1.25 Lug Nuts with a Conical 60 Degree seating surface. Safe wheel offset range is +35mm to +48mm.

Factory OEM Wheel & Tire Configurations (2023)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
Base (17") 17x7.5 ET+48
215/45R17 (Michelin Primacy HP) Compare ⚡
35 PSI Find Tires →
Premium / Trueno Edition (18" Matte Black) 18x7.5 ET+48
215/40R18 (Michelin Pilot Sport 4) Compare ⚡
35 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Toyota GR86 factory 56.1 mm hub snout.

Factory Hub: 56.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +17.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 56.1mm (OD: 73.1mm / ID: 56.1mm)
🛒 Order 73.1mm to 56.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 7.5" ET48
New Wheel Width:8.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET38 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x100
2022-2026 FITMENT SPECIFICATION

2023 Toyota GR86

fitmentspec.com/toyota/gr86/2023
FINAL TORQUE89 ft-lbs(120 Nm)
Bolt Pattern (PCD)5x100
Center Bore56.1 mm
Fastener & ThreadM12 x 1.25Lug Nut • Conical 60 Degree
TPMS CalibrationDirect Tire Pressure SensorDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x100 bolt pattern and 56.1 mm hub bore.

✓ No Centering Rings Required
2013-201656.1 mm CB
Scion FR-S
Torque: 89 ft-lbsSpecs →
2022-202656.1 mm CB
Subaru BRZ
Torque: 89 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +8.09" (+32.86%)
+32.86%
Original Baseline Tire215/45R17
New Target Tire285/70R17
QUICK SIZES:
24.6"32.7"
Speedometer Variance Table
30 mph gauge39.9 actual+9.9 mph
45 mph gauge59.8 actual+14.8 mph
60 mph gauge79.7 actual+19.7 mph
70 mph gauge93.0 actual+23.0 mph
80 mph gauge106.3 actual+26.3 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
205/50R16
Mounted on 16x6.5" Wheel
PCD: 5x100
Center Bore: 56.1 mm
🛡️ Technical Benefits for 2023 Toyota GR86
⛷️ Higher Ground Pressure
A narrower tire (205mm vs 215mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TIRE PRESSURE SENSOR TPMS433 MHz
Architecture
Indirect Wheel Speed ABS
Sensor Part Number
SU003-08502
Relearn Protocol
Glovebox TPMS Switch / Gauge Cluster Relearn
Relearn Sequence0 / 1 Steps Complete
1
Adjust tires to 35 PSI cold. Press and hold the TPMS set button located inside the glovebox (or via cluster vehicle settings) until the TPMS light blinks 3 times. Drive for 15 minutes.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2023 GR86

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2023 Toyota GR86)

8 Verified Q&As
Q What is the bolt pattern for a 2023 Toyota GR86?
The factory bolt pattern (PCD) for the 2023 Toyota GR86 is 5x100 (5-lug configuration) with a pitch circle diameter of 100 mm. Center bore hub diameter is 56.1 mm.
Q What is the wheel lug torque specification for a 2023 Toyota GR86?
The official factory wheel lug torque specification for the 2023 Toyota GR86 is 89 ft-lbs (120 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2023 Toyota GR86?
The manufacturer does not rate or recommend the 2023 Toyota GR86 for trailer towing. Installing an aftermarket trailer hitch receiver is not advised for towing loads and may void powertrain warranty.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2023 Toyota GR86?
Factory stock tire sizing for the 2023 Toyota GR86 is 215/45R17 (Michelin Primacy HP) with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2023 Toyota GR86 and are hub centric rings needed?
The center bore diameter is exactly 56.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 56.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2023 Toyota GR86 use?
The 2023 Toyota GR86 utilizes M12 x 1.25 Lug Nuts with a Conical 60 Degree seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2023 Toyota GR86 have Direct or Indirect TPMS and how is it reset?
This vehicle utilizes standard valve stems without requiring active electronic TPMS sensor recalibration.
Q What aftermarket wheel offset and tire sizes fit a 2023 Toyota GR86 without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +35mm and +48mm with a flush target of ET +38. Always test clearance at full steering lock.