FitmentSpec Logo
Toyota logo
1st Gen AS10 (XLE / Limited / Platinum Hybrid MAX 362 HP 3-Row) (2024–2026)

2026 Toyota Grand Highlander

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2026 Toyota Grand Highlander
OEM Powertrain Standard Specification
Chassis Dimensions Exterior & Curb Weight
Center BoreHub Centric
60.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+35 to +45
Flush Target: ET +40
Lug TorqueM14 x 1.5
103 ft-lbs
140 Nm • Conical Seat
Fastener: Conical Seat 60 Degree Lug Bolt. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2026 Toyota Grand Highlander Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 5,000 lbs
Max Towing (Braked)
5,000 lbs
2,268 kg
With factory trailer brakes
Max Payload Capacity
1,450 lbs
658 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
500 lbs
227 kg
Maximum hitch downward load
Hitch Receiver Class
Class III (2-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2026 Grand Highlander
Selected Load: 5,000 lbs • Vehicle Rating: 5,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Rated up to 5,000 lbs when equipped with factory heavy-duty trailer tow package and auxiliary transmission cooler.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 1500 lbs (680 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2026 Toyota Grand Highlander Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2026 Toyota Grand Highlander? The factory bolt pattern is 5x114.3 (5-lug) with a 60.1 mm center bore. The manufacturer specified wheel lug torque is 103 ft-lbs (140 Nm) using M14 x 1.5 Lug Bolts with a Conical Seat 60 Degree seating surface. Safe wheel offset range is +35mm to +45mm.

Factory OEM Wheel & Tire Configurations (2026)

1 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
Hybrid MAX Platinum (20" Two-Tone Multi-Spoke Clad Alloy) 20x8 ET+40
255/55R20 Compare ⚡
32-35 PSI Placard Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Toyota Grand Highlander factory 60.1 mm hub snout.

Factory Hub: 60.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +13.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 60.1mm (OD: 73.1mm / ID: 60.1mm)
🛒 Order 73.1mm to 60.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 8" ET40
New Wheel Width:9.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET30 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x114.3
2024-2026 FITMENT SPECIFICATION

2026 Toyota Grand Highlander

fitmentspec.com/toyota/grand-highlander/2026
FINAL TORQUE103 ft-lbs(140 Nm)
Bolt Pattern (PCD)5x114.3
Center Bore60.1 mm
Fastener & ThreadM14 x 1.5Lug Bolt • Conical Seat 60 Degree
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x114.3 bolt pattern and 60.1 mm hub bore.

✓ No Centering Rings Required
2019-202660.1 mm CB
Lexus ES
Torque: 103 ft-lbsSpecs →
2014-202660.1 mm CB
Lexus IS
Torque: 103 ft-lbsSpecs →
2022-202660.1 mm CB
Lexus NX
Torque: 103 ft-lbsSpecs →
2023-202660.1 mm CB
Lexus RX
Torque: 103 ft-lbsSpecs →
2024-202660.1 mm CB
Lexus TX
Torque: 103 ft-lbsSpecs →
2018-202460.1 mm CB
Toyota Camry
Torque: 103 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Significant DifferenceDiameter: +1.67" (+5.36%)
+5.36%
Original Baseline Tire255/55R20
New Target Tire285/70R17
QUICK SIZES:
31.0"32.7"
Speedometer Variance Table
30 mph gauge31.6 actual+1.6 mph
45 mph gauge47.4 actual+2.4 mph
60 mph gauge63.2 actual+3.2 mph
70 mph gauge73.8 actual+3.8 mph
80 mph gauge84.3 actual+4.3 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
235/65R18
Mounted on 18x7.0" Wheel
PCD: 5x114.3
Center Bore: 60.1 mm
🛡️ Technical Benefits for 2026 Toyota Grand Highlander
⛷️ Higher Ground Pressure
A narrower tire (235mm vs 255mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Auto-Relearn Drive Cycle
Relearn Sequence0 / 1 Steps Complete
1
Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2026 Grand Highlander

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2026 Toyota Grand Highlander)

8 Verified Q&As
Q What is the bolt pattern for a 2026 Toyota Grand Highlander?
The factory bolt pattern (PCD) for the 2026 Toyota Grand Highlander is 5x114.3 (5-lug configuration) with a pitch circle diameter of 114.3 mm. Center bore hub diameter is 60.1 mm.
Q What is the wheel lug torque specification for a 2026 Toyota Grand Highlander?
The official factory wheel lug torque specification for the 2026 Toyota Grand Highlander is 103 ft-lbs (140 Nm). Tighten all Lug Bolts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2026 Toyota Grand Highlander?
The official maximum braked towing capacity for the 2026 Toyota Grand Highlander is 5,000 lbs (2,268 kg) with a maximum tongue weight limit of 500 lbs. Recommended hitch receiver: Class III (2-inch Receiver). Unbraked trailer limit is 1,500 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2026 Toyota Grand Highlander?
Factory stock tire sizing for the 2026 Toyota Grand Highlander is 255/55R20 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2026 Toyota Grand Highlander and are hub centric rings needed?
The center bore diameter is exactly 60.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 60.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2026 Toyota Grand Highlander use?
The 2026 Toyota Grand Highlander utilizes M14 x 1.5 Lug Bolts with a Conical Seat 60 Degree seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2026 Toyota Grand Highlander have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn Drive Cycle: Drive vehicle above 15 mph (25 km/h) for up to 20 minutes to automatically synchronize sensor IDs.
Q What aftermarket wheel offset and tire sizes fit a 2026 Toyota Grand Highlander without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +35mm and +45mm with a flush target of ET +40. Always test clearance at full steering lock.