FitmentSpec Logo
Toyota logo
XL40 (4th Gen - All-Hybrid) (2021–2026)

2024 Toyota Sienna

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2024 Toyota Sienna
Factory Powertrain 2.5L DOHC 4-Cylinder Hybrid A25A-FXS
245 HP (183 kW) 176 lb-ft 2.5L Inline-4 Hybrid
Chassis Dimensions Exterior & Curb Weight
L: 203.7" W: 78.5" WB: 120.5" 4,610 - 4,725 lbs lbs
Center BoreHub Centric
60.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+30 to +45
Flush Target: ET +30
Lug TorqueM12 x 1.5
76 ft-lbs
103 Nm • Mag Seat
Fastener: Mag Seat with Flat Washer (OEM) / Conical (Aftermarket) Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2024 Toyota Sienna Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 3,500 lbs
Max Towing (Braked)
3,500 lbs
1,588 kg
With factory trailer brakes
Max Payload Capacity
1,335 lbs
606 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
350 lbs
159 kg
Maximum hitch downward load
Hitch Receiver Class
Class II (2-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2024 Sienna
Selected Load: 3,500 lbs • Vehicle Rating: 3,500 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Standard 3,500 lbs towing on 2.5L Hybrid powertrain with standard Electronic Trailer Sway Control (TSC).

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 1225 lbs (556 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2024 Toyota Sienna Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2024 Toyota Sienna? The factory bolt pattern is 5x114.3 (5-lug) with a 60.1 mm center bore. The manufacturer specified wheel lug torque is 76 ft-lbs (103 Nm) using M12 x 1.5 Lug Nuts with a Mag Seat with Flat Washer (OEM) / Conical (Aftermarket) seating surface. Safe wheel offset range is +30mm to +45mm.

Factory OEM Wheel & Tire Configurations (2024)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
LE / XLE / Woodland Edition (17"-18") 17x7 ET+35
235/65R17 Compare ⚡
35 PSI Find Tires →
XSE / Platinum (20" Split-Spoke Dark) 20x7.5 ET+35
235/50R20 Compare ⚡
36 PSI Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Toyota Sienna factory 60.1 mm hub snout.

Factory Hub: 60.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +13.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 60.1mm (OD: 73.1mm / ID: 60.1mm)
🛒 Order 73.1mm to 60.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 7" ET35
New Wheel Width:8.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET25 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x114.3
2021-2026 FITMENT SPECIFICATION

2024 Toyota Sienna

fitmentspec.com/toyota/sienna/2024
FINAL TORQUE76 ft-lbs(103 Nm)
Bolt Pattern (PCD)5x114.3
Center Bore60.1 mm
Fastener & ThreadM12 x 1.5Lug Nut • Mag Seat with Flat Washer (OEM) / Conical (Aftermarket)
TPMS CalibrationDirect Tire Pressure Monitoring SensorDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x114.3 bolt pattern and 60.1 mm hub bore.

✓ No Centering Rings Required
2019-202660.1 mm CB
Lexus ES
Torque: 76 ft-lbsSpecs →
2014-202660.1 mm CB
Lexus IS
Torque: 76 ft-lbsSpecs →
2022-202660.1 mm CB
Lexus NX
Torque: 76 ft-lbsSpecs →
2023-202660.1 mm CB
Lexus RX
Torque: 76 ft-lbsSpecs →
2024-202660.1 mm CB
Lexus TX
Torque: 76 ft-lbsSpecs →
2018-202460.1 mm CB
Toyota Camry
Torque: 76 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +3.68" (+12.68%)
+12.68%
Original Baseline Tire235/65R17
New Target Tire285/70R17
QUICK SIZES:
29.0"32.7"
Speedometer Variance Table
30 mph gauge33.8 actual+3.8 mph
45 mph gauge50.7 actual+5.7 mph
60 mph gauge67.6 actual+7.6 mph
70 mph gauge78.9 actual+8.9 mph
80 mph gauge90.1 actual+10.1 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
225/70R16
Mounted on 16x6.5" Wheel
PCD: 5x114.3
Center Bore: 60.1 mm
🛡️ Technical Benefits for 2024 Toyota Sienna
⛷️ Higher Ground Pressure
A narrower tire (225mm vs 235mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TIRE PRESSURE MONITORING SENSOR TPMS315 MHz
Architecture
Indirect Wheel Speed ABS
Sensor Part Number
42607-02050
Relearn Protocol
Instrument Cluster Menu Reset
Relearn Sequence0 / 1 Steps Complete
1
Ensure 35-36 PSI cold. In cluster: Settings > Vehicle Settings > TPWS > Tire Pressure Setting. Hold OK until TPWS indicator flashes 3 times.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →
🔩

Verified Hardware & Installation Kit for 2024 Sienna

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2024 Toyota Sienna)

8 Verified Q&As
Q What is the bolt pattern for a 2024 Toyota Sienna?
The factory bolt pattern (PCD) for the 2024 Toyota Sienna is 5x114.3 (5-lug configuration) with a pitch circle diameter of 114.3 mm. Center bore hub diameter is 60.1 mm.
Q What is the wheel lug torque specification for a 2024 Toyota Sienna?
The official factory wheel lug torque specification for the 2024 Toyota Sienna is 76 ft-lbs (103 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2024 Toyota Sienna?
The official maximum braked towing capacity for the 2024 Toyota Sienna is 3,500 lbs (1,588 kg) with a maximum tongue weight limit of 350 lbs. Recommended hitch receiver: Class II (2-inch Receiver). Unbraked trailer limit is 1,225 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2024 Toyota Sienna?
Factory stock tire sizing for the 2024 Toyota Sienna is 235/65R17 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2024 Toyota Sienna and are hub centric rings needed?
The center bore diameter is exactly 60.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 60.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2024 Toyota Sienna use?
The 2024 Toyota Sienna utilizes M12 x 1.5 Lug Nuts with a Mag Seat with Flat Washer (OEM) / Conical (Aftermarket) seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2024 Toyota Sienna have Direct or Indirect TPMS and how is it reset?
This vehicle utilizes standard valve stems without requiring active electronic TPMS sensor recalibration.
Q What aftermarket wheel offset and tire sizes fit a 2024 Toyota Sienna without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +30mm and +45mm with a flush target of ET +30. Always test clearance at full steering lock.