FitmentSpec Logo
Toyota logo
3rd & 4th Gen XP130/XP210 (L / LE / SE / Icon / Design / Excel / Hybrid) (2012–2026)

2013 Toyota Yaris

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2013 Toyota Yaris
Factory Powertrain 1.5L Dynamic Force 3-Cylinder / Hybrid
114 HP (85 kW) 104 lb-ft 1.5L Inline-3
Chassis Dimensions Exterior & Curb Weight
L: 155.1" W: 68.7" WB: 100.8" 2,290 – 2,560 lbs lbs
Bolt Pattern4-Lug
4x100
Center BoreHub Centric
54.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+38 to +48
Flush Target: ET +38
Lug TorqueM12x1.5
76 ft-lbs
103 Nm • Conical Seat
Fastener: Conical 60deg Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2013 Toyota Yaris Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 1,870 lbs
Max Towing (Braked)
1,870 lbs
848 kg
With factory trailer brakes
Max Payload Capacity
925 lbs
420 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
187 lbs
85 kg
Maximum hitch downward load
Hitch Receiver Class
Class III (2-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2013 Yaris
Selected Load: 1,870 lbs • Vehicle Rating: 1,870 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Adhere to factory towing manual limits and trailer tongue weight balance.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 655 lbs (297 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2013 Toyota Yaris Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2013 Toyota Yaris? The factory bolt pattern is 4x100 (4-lug) with a 54.1 mm center bore. The manufacturer specified wheel lug torque is 76 ft-lbs (103 Nm) using M12x1.5 Lug Nuts with a Conical 60deg seating surface. Safe wheel offset range is +38mm to +48mm.

Factory OEM Wheel & Tire Configurations (2013)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
15" Base / L / LE / Icon Steel & Alloy 15x5.5 ET+45
185/60R15 Compare ⚡
32 / 32 PSI Find Tires →
16" SE / Design / Hybrid Alloy 16x6 ET+45
185/55R16 Compare ⚡
32 / 30 PSI Find Tires →

🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues

1 DOCUMENTED ISSUES
Front Suspension & Strut Top Mounts Low Severity
Symptom

Rattling or clunking noise when traversing small road imperfections at low speeds

Root Cause & TSB Details

Premature wear in front upper strut mount rubber bushings and axial bearings

Affected Components: Strut Mount BushingAxial BearingSway Bar End Links
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Toyota Yaris factory 54.1 mm hub snout.

Factory Hub: 54.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +19.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 54.1mm (OD: 73.1mm / ID: 54.1mm)
🛒 Order 73.1mm to 54.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 5.5" ET45
New Wheel Width:6.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET35 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

4x100
2012-2026 FITMENT SPECIFICATION

2013 Toyota Yaris

fitmentspec.com/toyota/yaris/2013
FINAL TORQUE76 ft-lbs(103 Nm)
Bolt Pattern (PCD)4x100
Center Bore54.1 mm
Fastener & ThreadM12x1.5Lug Nut • Conical 60deg
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +8.97" (+37.78%)
+37.78%
Original Baseline Tire185/60R15
New Target Tire285/70R17
QUICK SIZES:
23.7"32.7"
Speedometer Variance Table
30 mph gauge41.3 actual+11.3 mph
45 mph gauge62.0 actual+17.0 mph
60 mph gauge82.7 actual+22.7 mph
70 mph gauge96.4 actual+26.4 mph
80 mph gauge110.2 actual+30.2 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
205/65R16
Mounted on 16x6.5" Wheel
PCD: 4x100
Center Bore: 54.1 mm
🛡️ Technical Benefits for 2013 Toyota Yaris
⛷️ Higher Ground Pressure
A narrower tire (205mm vs 185mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS315 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
42607-02031
Relearn Protocol
Cluster-Reset
Relearn Sequence0 / 5 Steps Complete
1
Inflate all tires to recommended placard pressure.
2
Turn ignition to ON (engine off).
3
Press and hold TPMS set button beneath steering column or access Vehicle Settings in gauge cluster.
4
Hold until tire pressure warning light blinks 3 times slowly.
5
Drive vehicle for 15-30 minutes at speeds above 25 mph to finalize sensor registration.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →

🔍 Pre-Purchase Fitment & Chassis Inspection Checklist

Universal 8-Point Buyer Guide →

✓ Wheel Hub & Bearing Inspection

  • • Check 54.1mm center hub spigot for corrosion; clean hub mating face prior to mounting alloy wheels.
  • • Verify 12 o'clock and 6 o'clock wheel bearing play on lift.

✓ Suspension & Steering Clearance

  • • Verify inner tire clearance to front MacPherson struts when opting for 7.0-inch or wider wheels.
  • • Check rear torsion beam bushings for dry cracking or elongation.
Brake Caliper Clearance Note

Front single-piston calipers clear all OEM 15-inch and larger wheels; minimum 15-inch wheel diameter required.

Common Wear Replacement Parts

📋 One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

🔩

Verified Hardware & Installation Kit for 2013 Yaris

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2013 Toyota Yaris)

8 Verified Q&As
Q What is the bolt pattern for a 2013 Toyota Yaris?
The factory bolt pattern (PCD) for the 2013 Toyota Yaris is 4x100 (4-lug configuration) with a pitch circle diameter of 100 mm. Center bore hub diameter is 54.1 mm.
Q What is the wheel lug torque specification for a 2013 Toyota Yaris?
The official factory wheel lug torque specification for the 2013 Toyota Yaris is 76 ft-lbs (103 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2013 Toyota Yaris?
The official maximum braked towing capacity for the 2013 Toyota Yaris is 1,870 lbs (848 kg) with a maximum tongue weight limit of 187 lbs. Recommended hitch receiver: Class III (2-inch Receiver). Unbraked trailer limit is 655 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2013 Toyota Yaris?
Factory stock tire sizing for the 2013 Toyota Yaris is 185/60R15 with a recommended cold tire pressure of 32 PSI front and 32 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2013 Toyota Yaris and are hub centric rings needed?
The center bore diameter is exactly 54.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 54.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2013 Toyota Yaris use?
The 2013 Toyota Yaris utilizes M12x1.5 Lug Nuts with a Conical 60deg seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2013 Toyota Yaris have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 315 MHz. The relearn protocol is Cluster-Reset: Inflate all tires to recommended placard pressure.
Q What aftermarket wheel offset and tire sizes fit a 2013 Toyota Yaris without rubbing?
For an aggressive yet flush aesthetic without fender rolling or rubbing, the recommended setup is 16x6.5 ET40 wheels with 195/50R16 tires. For a 100% rub-free conservative upgrade, choose 15x6.0 ET42 with 185/60R15. Factory safe offset range spans +38mm to +48mm.

⚠️ Official NHTSA Safety Recalls & Bulletins

NHTSA #21V034000 • Electronic Stability Control / Radar Sensor

Toyota recalled certain Yaris models due to millimeter wave radar sensor initialization errors.

Remedy: Dealers re-calibrate millimeter wave radar sensor and software free of charge.