2022 Ford Bronco
Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.
2022 Ford Bronco Towing Capacity & Hitch Telemetry
Official manufacturer braked tow ratings, max tongue weight, and payload limits.
Bronco Raptor rated at 4,500 lbs; 2-door and 4-door models with 2.3L/2.7L EcoBoost and Towing Capability Package rated at 3,500 lbs.
- • Unbraked trailer maximum limit: 1500 lbs (680 kg).
- • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
- • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.
2022 Ford Bronco Quick Fitment Answers
Looking for exact hub and wheel specifications for the 2022 Ford Bronco? The factory bolt pattern is 6x139.7 (6-lug) with a 93.1 mm center bore. The manufacturer specified wheel lug torque is 100 ft-lbs (135 Nm) using M12x1.5 Lug Nuts with a Conical 60° seating surface. Safe wheel offset range is +20mm to +55mm.
Factory OEM Wheel & Tire Configurations (2022)
2 TRIM OPTIONS| Trim Name | Wheel Size | Tire Specification | Placard PSI | Equipment |
|---|---|---|---|---|
| Base / Big Bend | 17x7.5 ET+55 | 255/75R17
Compare ⚡
| 35 / 35 PSI | Find Tires → |
| Sasquatch Package | 17x8.5 ET+30 | 315/70R17
Compare ⚡
| 39 / 39 PSI | Find Tires → |
🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues
1 DOCUMENTED ISSUESSnapping or bending of inner/outer tie rods under off-road articulation with 35+ inch tires
Cast aluminum steering gear housing and standard-duty tie rods under extreme rock crawl loads (Ford TSB 22-2144)
Hub Centric Ring Finder & Vibration Eliminator
Precision adapter sizing for Ford Bronco factory 93.1 mm hub snout.
The wheel bore (73.1 mm) is smaller than the car hub (93.1 mm). The wheel will NOT physically seat flush on the hub face without wheel spacers or center-bore machining.
OEM vs. Aftermarket Visual Stance & Poke Gauge
Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.
Printable Mechanic Spec Card & Torque Sequence
High-contrast pocket card for tire shops, track days, and garage toolboxes.
2022 Ford Bronco
fitmentspec.com/ford/bronco/2022DIRECT HUB-CENTRIC WHEEL INTERCHANGE
Vehicles sharing both the exact 6x139.7 bolt pattern and 93.1 mm hub bore.
Cross-Vehicle OEM Wheel Swap Compatibility (6x139.7)
Verified OEM donor vehicles whose factory wheels fit the Ford Bronco hub (93.1mm).
Ford Bronco Raptor
Ford Ranger

Cadillac Escalade
Chevrolet Colorado

Chevrolet Silverado 1500

Chevrolet Silverado 1500

Chevrolet Suburban

Chevrolet Tahoe
⚡ Will It Rub? 2D Offset & Strut Clearance
Real-time inner strut clearance and outer fender poke calculation.
WINTER WHEEL & MINUS-SIZING ADVISOR
Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.
📡 TPMS Protocol & Relearn Procedure
US OEM Sensor Protocol & Step-by-Step Calibration
🔍 Pre-Purchase Fitment & Chassis Inspection Checklist
Universal 8-Point Buyer Guide →✓ Wheel Hub & Bearing Inspection
- • Check 93.1mm front wheel hub bearings for play after running negative offset wheels.
- • Inspect axle halfshaft CV boots for tears.
✓ Suspension & Steering Clearance
- • Verify front crash bars are intact or properly removed if running 35-inch tires.
- • Check rear track bar bracket.
Standard 17-inch wheels clear calipers; certain 16-inch aftermarket rims contact the front tie-rod end and caliper.
📋 One-Click Forum Spec Exporter
Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).