2013 Honda Fit
Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.
2013 Honda Fit Towing Capacity & Hitch Telemetry
Official manufacturer braked tow ratings, max tongue weight, and payload limits.
Adhere to factory towing manual limits and trailer tongue weight balance.
- • Unbraked trailer maximum limit: 350 lbs (159 kg).
- • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
- • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.
2013 Honda Fit Quick Fitment Answers
Looking for exact hub and wheel specifications for the 2013 Honda Fit? The factory bolt pattern is 4x100 (4-lug) with a 56.1 mm center bore. The manufacturer specified wheel lug torque is 80 ft-lbs (108 Nm) using M12x1.5 Lug Nuts with a Conical 60deg seating surface. Safe wheel offset range is +40mm to +53mm.
Factory OEM Wheel & Tire Configurations (2013)
2 TRIM OPTIONS| Trim Name | Wheel Size | Tire Specification | Placard PSI | Equipment |
|---|---|---|---|---|
| 15" Base / LX Steel & Alloy | 15x5.5 ET+45 | 175/65R15
Compare ⚡
| 33 / 32 PSI | Find Tires → |
| 16" Sport / EX / EX-L Alloy | 16x6 ET+50 | 185/55R16
Compare ⚡
| 33 / 32 PSI | Find Tires → |
🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues
1 DOCUMENTED ISSUESEngine misfire, rough idle, and check engine light DTC P0300-P0304
Carbon buildup on direct-injection intake valves and injector clogging (TSB 16-034)
Hub Centric Ring Finder & Vibration Eliminator
Precision adapter sizing for Honda Fit factory 56.1 mm hub snout.
The wheel bore is +17.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:
OEM vs. Aftermarket Visual Stance & Poke Gauge
Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.
Printable Mechanic Spec Card & Torque Sequence
High-contrast pocket card for tire shops, track days, and garage toolboxes.
2013 Honda Fit
fitmentspec.com/honda/fit/2013⚡ Will It Rub? 2D Offset & Strut Clearance
Real-time inner strut clearance and outer fender poke calculation.
WINTER WHEEL & MINUS-SIZING ADVISOR
Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.
📡 TPMS Protocol & Relearn Procedure
US OEM Sensor Protocol & Step-by-Step Calibration
🔍 Pre-Purchase Fitment & Chassis Inspection Checklist
Universal 8-Point Buyer Guide →✓ Wheel Hub & Bearing Inspection
- • Inspect front hub bearings for humming noise between 40-60 mph; 56.1mm hub face must be clean and unpitted.
- • Ensure OEM lug nuts have ball/spherical seat on factory Honda rims, or use 60° conical nuts for aftermarket wheels.
✓ Suspension & Steering Clearance
- • Check clearance between front MacPherson strut spring perch and wide aftermarket wheels (>7.0-inch width).
- • Inspect rear torsion beam center rubber bushings for cracking.
Front single-piston calipers clear OEM 15-inch and 16-inch wheels easily; clearance issues rare unless installing custom BBK.
📋 One-Click Forum Spec Exporter
Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).
Verified Hardware & Installation Kit for 2013 Fit
Frequently Asked Questions (2013 Honda Fit)
Q What is the bolt pattern for a 2013 Honda Fit?
Q What is the wheel lug torque specification for a 2013 Honda Fit?
Q What is the towing capacity of a 2013 Honda Fit?
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2013 Honda Fit?
Q What is the center bore size on a 2013 Honda Fit and are hub centric rings needed?
Q What size lug nuts and thread pitch does a 2013 Honda Fit use?
Q Does the 2013 Honda Fit have Direct or Indirect TPMS and how is it reset?
Q What aftermarket wheel offset and tire sizes fit a 2013 Honda Fit without rubbing?
⚠️ Official NHTSA Safety Recalls & Bulletins
Honda recalled certain 2009-2014 Fit models due to drive shafts susceptible to corrosion breakage under road salt exposure.