FitmentSpec Logo
Honda logo
2nd, 3rd & 4th Gen GE/GK/GR (Base / Sport / EX / EX-L / Jazz / e:HEV) (2009–2026)

2024 Honda Fit

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2024 Honda Fit
Factory Powertrain 1.5L Earth Dreams i-VTEC / e:HEV Hybrid
130 HP (97 kW) 114 lb-ft 1.5L Inline-4
Chassis Dimensions Exterior & Curb Weight
L: 161.4" W: 67" WB: 99.6" 2,513 – 2,648 lbs lbs
Bolt Pattern4-Lug
4x100
Center BoreHub Centric
56.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+40 to +53
Flush Target: ET +40
Lug TorqueM12x1.5
80 ft-lbs
108 Nm • Conical Seat
Fastener: Conical 60deg Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2024 Honda Fit Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 1,000 lbs
Max Towing (Braked)
1,000 lbs
454 kg
With factory trailer brakes
Max Payload Capacity
850 lbs
386 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
100 lbs
45 kg
Maximum hitch downward load
Hitch Receiver Class
Class III (2-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2024 Fit
Selected Load: 1,000 lbs • Vehicle Rating: 1,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Adhere to factory towing manual limits and trailer tongue weight balance.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 350 lbs (159 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2024 Honda Fit Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2024 Honda Fit? The factory bolt pattern is 4x100 (4-lug) with a 56.1 mm center bore. The manufacturer specified wheel lug torque is 80 ft-lbs (108 Nm) using M12x1.5 Lug Nuts with a Conical 60deg seating surface. Safe wheel offset range is +40mm to +53mm.

Factory OEM Wheel & Tire Configurations (2024)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
15" Base / LX Steel & Alloy 15x5.5 ET+45
175/65R15 Compare ⚡
33 / 32 PSI Find Tires →
16" Sport / EX / EX-L Alloy 16x6 ET+50
185/55R16 Compare ⚡
33 / 32 PSI Find Tires →

🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues

1 DOCUMENTED ISSUES
Fuel Injection System (GK5) Moderate Severity
Symptom

Engine misfire, rough idle, and check engine light DTC P0300-P0304

Root Cause & TSB Details

Carbon buildup on direct-injection intake valves and injector clogging (TSB 16-034)

Affected Components: Direct Fuel InjectorsHigh Pressure Fuel RailIntake Valves
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Honda Fit factory 56.1 mm hub snout.

Factory Hub: 56.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +17.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 56.1mm (OD: 73.1mm / ID: 56.1mm)
🛒 Order 73.1mm to 56.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 5.5" ET45
New Wheel Width:6.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET35 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

4x100
2009-2026 FITMENT SPECIFICATION

2024 Honda Fit

fitmentspec.com/honda/fit/2024
FINAL TORQUE80 ft-lbs(108 Nm)
Bolt Pattern (PCD)4x100
Center Bore56.1 mm
Fastener & ThreadM12x1.5Lug Nut • Conical 60deg
TPMS CalibrationIndirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +8.75" (+36.53%)
+36.53%
Original Baseline Tire175/65R15
New Target Tire285/70R17
QUICK SIZES:
24.0"32.7"
Speedometer Variance Table
30 mph gauge41.0 actual+11.0 mph
45 mph gauge61.4 actual+16.4 mph
60 mph gauge81.9 actual+21.9 mph
70 mph gauge95.6 actual+25.6 mph
80 mph gauge109.2 actual+29.2 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
205/70R16
Mounted on 16x6.5" Wheel
PCD: 4x100
Center Bore: 56.1 mm
🛡️ Technical Benefits for 2024 Honda Fit
⛷️ Higher Ground Pressure
A narrower tire (205mm vs 175mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

INDIRECT TPMSABS Wheel Speed Based
Architecture
Indirect Wheel Speed ABS
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Cluster-Reset
Relearn Sequence0 / 4 Steps Complete
1
Ensure all 4 tires are inflated to cold placard specifications.
2
Turn vehicle ON with engine running or in accessory mode.
3
Press and hold the TPMS calibration button to the lower left of steering wheel until TPMS indicator blinks twice.
4
Drive vehicle between 30 and 65 mph for approximately 20 minutes to complete ABS wheel-speed sensor calibration.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →

🔍 Pre-Purchase Fitment & Chassis Inspection Checklist

Universal 8-Point Buyer Guide →

✓ Wheel Hub & Bearing Inspection

  • • Inspect front hub bearings for humming noise between 40-60 mph; 56.1mm hub face must be clean and unpitted.
  • • Ensure OEM lug nuts have ball/spherical seat on factory Honda rims, or use 60° conical nuts for aftermarket wheels.

✓ Suspension & Steering Clearance

  • • Check clearance between front MacPherson strut spring perch and wide aftermarket wheels (>7.0-inch width).
  • • Inspect rear torsion beam center rubber bushings for cracking.
Brake Caliper Clearance Note

Front single-piston calipers clear OEM 15-inch and 16-inch wheels easily; clearance issues rare unless installing custom BBK.

Common Wear Replacement Parts

📋 One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

🔩

Verified Hardware & Installation Kit for 2024 Fit

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2024 Honda Fit)

8 Verified Q&As
Q What is the bolt pattern for a 2024 Honda Fit?
The factory bolt pattern (PCD) for the 2024 Honda Fit is 4x100 (4-lug configuration) with a pitch circle diameter of 100 mm. Center bore hub diameter is 56.1 mm.
Q What is the wheel lug torque specification for a 2024 Honda Fit?
The official factory wheel lug torque specification for the 2024 Honda Fit is 80 ft-lbs (108 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2024 Honda Fit?
The official maximum braked towing capacity for the 2024 Honda Fit is 1,000 lbs (454 kg) with a maximum tongue weight limit of 100 lbs. Recommended hitch receiver: Class III (2-inch Receiver). Unbraked trailer limit is 350 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2024 Honda Fit?
Factory stock tire sizing for the 2024 Honda Fit is 175/65R15 with a recommended cold tire pressure of 33 PSI front and 32 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2024 Honda Fit and are hub centric rings needed?
The center bore diameter is exactly 56.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 56.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2024 Honda Fit use?
The 2024 Honda Fit utilizes M12x1.5 Lug Nuts with a Conical 60deg seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2024 Honda Fit have Direct or Indirect TPMS and how is it reset?
It uses an Indirect TPMS system that calculates relative pressure by monitoring individual wheel rotation speeds via the ABS wheel speed sensors. Reset procedure: Cluster-Reset.
Q What aftermarket wheel offset and tire sizes fit a 2024 Honda Fit without rubbing?
For an aggressive yet flush aesthetic without fender rolling or rubbing, the recommended setup is 16x6.5 ET42 wheels with 195/50R16 tires. For a 100% rub-free conservative upgrade, choose 15x6.0 ET45 with 185/60R15. Factory safe offset range spans +40mm to +53mm.

⚠️ Official NHTSA Safety Recalls & Bulletins

NHTSA #20V770000 • Drive Shafts

Honda recalled certain 2009-2014 Fit models due to drive shafts susceptible to corrosion breakage under road salt exposure.

Remedy: Dealers inspect and replace drive shafts exhibiting corrosion or dynamic dampers free of charge.