FitmentSpec Logo
Hyundai logo
1st Gen NE (641 HP Dual-Motor AWD High-Performance EV) (2024โ€“2026)

2025 Hyundai Ioniq 5 N

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2025 Hyundai Ioniq 5 N
Factory Powertrain Dual Permanent-Magnet Synchronous EV Motors (601 HP Base / 641 HP N Grin Boost)
641 HP (478 kW) 568 lb-ft 0 Dual-Motor AWD EV
Chassis Dimensions Exterior & Curb Weight
L: 185.6" W: 76.4" WB: 118.1" 4,861 lbs (GVWR 5,864 lbs) lbs
Center BoreHub Centric
67.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+35 to +48
Flush Target: ET +38
Lug TorqueM14x1.5
137 ft-lbs
186 Nm โ€ข Conical Seat
Fastener: Conical 60ยฐ Lug Nut. Always re-torque after 50โ€“100 miles of driving.Get Torque Wrenchโ†’
โš ๏ธ
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer โ†’
โš“

2025 Hyundai Ioniq 5 N Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Towing Not Recommended
Max Towing (Braked)
0 lbs
Not Certified
Factory sports chassis
Max Payload Capacity
1,003 lbs
455 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
0 lbs
0 kg
Maximum hitch downward load
Hitch Receiver Class
Not Rated for Towing
Standard bumper / ball mount
๐Ÿ“‹ Factory Towing Guidance:

Hyundai officially rates the Ioniq 5 N at 0 lbs / 0 kg (Not Recommended for Towing) due to its rear aerodynamic diffuser, track-tuned thermal cooling architecture, and rear chassis bracing.

โš™๏ธ Essential Towing Safety Guidelines:
  • โ€ข Unbraked trailer maximum limit: 0 lbs (0 kg).
  • โ€ข Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • โ€ข Maintain tongue weight between 10%โ€“15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2025 Hyundai Ioniq 5 N Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2025 Hyundai Ioniq 5 N? The factory bolt pattern is 5x114.3 (5-lug) with a 67.1 mm center bore. The manufacturer specified wheel lug torque is 137 ft-lbs (186 Nm) using M14x1.5 Lug Nuts with a Conical 60ยฐ seating surface. Safe wheel offset range is +35mm to +48mm.

Factory OEM Wheel & Tire Configurations (2025)

1 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
N Performance (21" Forged Aluminum - Pirelli P Zero Elect HN) 21x9.5 ET+45 36 / 39 PSI Find Tires โ†’

๐Ÿ”ง Technical Service Bulletins (TSB) & Suspension Chronic Issues

3 DOCUMENTED ISSUES
M14x1.5 OEM Capped Lug Nut & Stud Sizing Confusion High Severity
Symptom

Deformed 21mm OEM lug nut caps or incorrect M12 replacement nuts failing to thread

Root Cause & TSB Details

Unlike the standard Ioniq 5 (M12x1.5 @ 79โ€“94 lb-ft), the Ioniq 5 N uses upgraded M14x1.5 studs torqued to 18.0โ€“20.0 kgfยทm (130โ€“145 lb-ft) with two-piece 21mm flower-head nuts.

Affected Components: M14x1.5 Wheel StudsOEM Two-Piece 21mm Lug Nuts
Integrated Charging Control Unit (ICCU) / 12V Auxiliary Drain High Severity
Symptom

Sudden 12V battery discharge or 'Check Electric Vehicle System' warning

Root Cause & TSB Details

Overcurrent spikes during AC charging/DC-DC conversion stress ICCU MOSFETs on E-GMP platforms.

Affected Components: ICCU Module12V Auxiliary Battery
Pirelli P Zero Elect (HN) PNCS Acoustic Foam Separation Moderate Severity
Symptom

High-speed steering wheel or seat vibration above 65 mph

Root Cause & TSB Details

Inner PNCS sound-absorbing foam ring inside 275/35R21 tires can delaminate after hard track heat cycles or pothole impacts.

Affected Components: 275/35R21 Pirelli P Zero Elect HN TiresPNCS Foam Liner
โญ•

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Hyundai Ioniq 5 N factory 67.1 mm hub snout.

Factory Hub: 67.1mm
Hub Diagnostic Result
โœ… HUB CENTRIC RINGS REQUIRED

The wheel bore is +6.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50โ€“75 mph, install this exact ring set:

73.1mm to 67.1mm (OD: 73.1mm / ID: 67.1mm)
๐Ÿ›’ Order 73.1mm to 67.1mm Ring Set on Amazonโ†—
๐Ÿ’ก Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
๐Ÿ“

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 9.5" ET45
New Wheel Width:10.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET35 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown๐Ÿ”ฅ WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
๐Ÿ“‹

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x114.3
2024-2026 FITMENT SPECIFICATION

2025 Hyundai Ioniq 5 N

fitmentspec.com/hyundai/ioniq-5-n/2025
FINAL TORQUE137 ft-lbs(186 Nm)
Bolt Pattern (PCD)5x114.3
Center Bore67.1 mm
Fastener & ThreadM14x1.5Lug Nut โ€ข Conical 60ยฐ
TPMS CalibrationDirectDoor Placard PSI
โญ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
โš ๏ธ NEVER USE IMPACT GUN FOR FINAL TORQUE
๐Ÿ”„

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x114.3 bolt pattern and 67.1 mm hub bore.

โœ“ No Centering Rings Required
2007-201067.1 mm CB
Alfa Romeo 8C Competizione
Torque: 137 ft-lbsSpecs โ†’
2022-202667.1 mm CB
Ferrari 296 GTB
Torque: 137 ft-lbsSpecs โ†’
2010-201567.1 mm CB
Ferrari 458 Italia
Torque: 137 ft-lbsSpecs โ†’
2016-202067.1 mm CB
Ferrari 488 GTB
Torque: 137 ft-lbsSpecs โ†’
2018-202467.1 mm CB
Ferrari 812 Superfast
Torque: 137 ft-lbsSpecs โ†’
2009-201767.1 mm CB
Ferrari California
Torque: 137 ft-lbsSpecs โ†’

โšก Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
โ–ฒ Recalibrate RequiredDiameter: +4.13" (+14.45%)
+14.45%
Original Baseline Tire275/35R21
New Target Tire285/70R17
QUICK SIZES:
28.6"32.7"
Speedometer Variance Table
30 mph gauge34.3 actual+4.3 mph
45 mph gauge51.5 actual+6.5 mph
60 mph gauge68.7 actual+8.7 mph
70 mph gauge80.1 actual+10.1 mph
80 mph gauge91.6 actual+11.6 mph
โ„๏ธ

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
255/45R19
Mounted on 19x8.5" Wheel
PCD: 5x114.3
Center Bore: 67.1 mm
๐Ÿ›ก๏ธ Technical Benefits for 2025 Hyundai Ioniq 5 N
โ›ท๏ธ Higher Ground Pressure
A narrower tire (255mm vs 275mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
๐Ÿ•ณ๏ธ Pothole Damage Protection
The taller aspect ratio (+10% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side โšก

๐Ÿ“ก TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
52940-T6100
Relearn Protocol
Auto-Relearn
Relearn Sequence0 / 3 Steps Complete
1
Inflate all four tires to US door-jamb placard cold pressure (36 PSI front / 39 PSI rear).
2
Ensure Ioniq 5 N-specific 433 MHz sensors (OEM 52940-T6100) are installed; standard Ioniq 5 sensors (-L1100/-L8200) are not cross-compatible.
3
Drive above 16 mph (25 km/h) for 10 to 20 minutes to complete automatic TPMS sensor ID synchronization.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon โ†’

๐Ÿ” Pre-Purchase Fitment & Chassis Inspection Checklist

Universal 8-Point Buyer Guide โ†’

โœ“ Wheel Hub & Bearing Inspection

  • โ€ข Confirm M14x1.5 wheel studs are clean and unstretched; verify OEM lug torque is within Hyundai N spec (130โ€“145 lb-ft / 177โ€“196 Nm).
  • โ€ข Inspect OEM 21-inch forged wheels for curb rash or two-piece lug nut cap swelling from impact wrenches.

โœ“ Suspension & Steering Clearance

  • โ€ข Inspect all four 275/35R21 Pirelli P Zero Elect (HN) tires for inner shoulder wear and PNCS acoustic foam separation vibration at highway speed.
  • โ€ข Check Electronic Controlled Suspension (ECS) dampers and e-LSD rear differential housing for fluid seepage or track-use heat discoloration.
Brake Caliper Clearance Note

Massive 400mm (15.7-inch) front rotors with 4-piston monobloc N calipers and 360mm rear rotors eliminate fitment of 18-inch and most 19-inch wheels; aftermarket 20-inch wheels must verify spoke/barrel clearance and M14 lug hole diameter.

Common Wear Replacement Parts

๐Ÿ“‹ One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

๐Ÿ”ฉ

Verified Hardware & Installation Kit for 2025 Ioniq 5 N

DIRECT OEM SPEC MATCH
๐Ÿ›ก๏ธOwner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2025 Hyundai Ioniq 5 N)

8 Verified Q&As
Q What is the bolt pattern for a 2025 Hyundai Ioniq 5 N?
The factory bolt pattern (PCD) for the 2025 Hyundai Ioniq 5 N is 5x114.3 (5-lug configuration) with a pitch circle diameter of 114.3 mm. Center bore hub diameter is 67.1 mm.
Q What is the wheel lug torque specification for a 2025 Hyundai Ioniq 5 N?
The official factory wheel lug torque specification for the 2025 Hyundai Ioniq 5 N is 137 ft-lbs (186 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2025 Hyundai Ioniq 5 N?
The manufacturer does not rate or recommend the 2025 Hyundai Ioniq 5 N for trailer towing. Installing an aftermarket trailer hitch receiver is not advised for towing loads and may void powertrain warranty.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2025 Hyundai Ioniq 5 N?
Factory stock tire sizing for the 2025 Hyundai Ioniq 5 N is 275/35R21 with a recommended cold tire pressure of 36 PSI front and 39 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2025 Hyundai Ioniq 5 N and are hub centric rings needed?
The center bore diameter is exactly 67.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 67.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2025 Hyundai Ioniq 5 N use?
The 2025 Hyundai Ioniq 5 N utilizes M14x1.5 Lug Nuts with a Conical 60ยฐ seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2025 Hyundai Ioniq 5 N have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn: Inflate all four tires to US door-jamb placard cold pressure (36 PSI front / 39 PSI rear).
Q What aftermarket wheel offset and tire sizes fit a 2025 Hyundai Ioniq 5 N without rubbing?
For an aggressive yet flush aesthetic without fender rolling or rubbing, the recommended setup is 21x9.5 ET+38 wheels with 275/35R21 tires. For a 100% rub-free conservative upgrade, choose 20x9.5 ET+45 with 275/40R20. Factory safe offset range spans +35mm to +48mm.

โš ๏ธ Official NHTSA Safety Recalls & Bulletins

NHTSA #25V-065 โ€ข SERVICE BRAKES, HYDRAULIC / VEHICLE SPEED CONTROL

Hyundai Recall 277 (superseding Recall 275 / updated under 26V068000): Integrated Electronic Brake (IEB) and Vehicle Control Unit (VCU) software logic defect when Left-Foot Braking (LFB) or N e-Shift is active on certain 2025 Ioniq 5 N vehicles.

Remedy: Hyundai dealers or Over-The-Air (OTA) update install revised IEB and VCU control software free of charge.
NHTSA #24V-868 โ€ข ELECTRICAL SYSTEM: INTEGRATED CHARGING CONTROL UNIT (ICCU)

E-GMP Integrated Charging Control Unit (ICCU) thermal/overcurrent stress can damage internal LDC transistors and fuse, preventing 12V auxiliary battery charging.

Remedy: Dealers inspect for ICCU DTCs, update ICCU software, and replace the ICCU assembly and fuse if faulted.