FitmentSpec Logo
Ram logo
5th Gen (DT) (2019–2026)

2019 Ram 1500

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2019 Ram 1500
Factory Powertrain 5.7L HEMI V8 with eTorque
395 HP (295 kW) 410 lb-ft 5.7L V8
Chassis Dimensions Exterior & Curb Weight
L: 232.9" W: 82.1" WB: 144.6" 4,798 – 5,372 lbs lbs
Center BoreHub Centric
77.8 mm
Hub Ring Spigot Diameter
Offset RangeET
+10 to +35
Flush Target: ET +18
Lug TorqueM14x1.5
130 ft-lbs
176 Nm • Conical Seat
Fastener: Conical 60° Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2019 Ram 1500 Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 1,000 lbs
Max Towing (Braked)
1,000 lbs
454 kg
With factory trailer brakes
Max Payload Capacity
850 lbs
386 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
100 lbs
45 kg
Maximum hitch downward load
Hitch Receiver Class
Class I (1.25-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2019 1500
Selected Load: 1,000 lbs • Vehicle Rating: 1,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Light duty towing up to 1,000 lbs. Recommended primarily for hitch-mounted accessories (bike racks, ski racks, cargo baskets).

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 350 lbs (159 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2019 Ram 1500 Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2019 Ram 1500? The factory bolt pattern is 6x139.7 (6-lug) with a 77.8 mm center bore. The manufacturer specified wheel lug torque is 130 ft-lbs (176 Nm) using M14x1.5 Lug Nuts with a Conical 60° seating surface. Safe wheel offset range is +10mm to +35mm.

Factory OEM Wheel & Tire Configurations (2019)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
Tradesman / Bighorn 18x8 ET+19
275/65R18 Compare ⚡
36 / 36 PSI Find Tires →
Laramie / Limited 20x9 ET+19
275/55R20 Compare ⚡
36 / 36 PSI Find Tires →

🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues

1 DOCUMENTED ISSUES
Rear Axle Differential & Pinion Bearing High Severity
Symptom

High-pitched whining or groaning noise on deceleration from 55 mph to 40 mph

Root Cause & TSB Details

Improper pinion pre-load and bearing wear in 9.25-inch rear axle (Stellantis TSB 03-001-20)

Affected Components: Rear Pinion BearingsRing and Pinion Gear SetAxle Seals
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Ram 1500 factory 77.8 mm hub snout.

Factory Hub: 77.8mm
Hub Diagnostic Result
🚨 INCOMPATIBLE WHEEL BORE (TOO SMALL)

The wheel bore (73.1 mm) is smaller than the car hub (77.8 mm). The wheel will NOT physically seat flush on the hub face without wheel spacers or center-bore machining.

💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 8" ET19
New Wheel Width:9.0" (+1.0" vs OEM)
New Wheel Offset (ET):ET9 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

6x139.7
2019-2026 FITMENT SPECIFICATION

2019 Ram 1500

fitmentspec.com/ram/1500/2019
FINAL TORQUE130 ft-lbs(176 Nm)
Bolt Pattern (PCD)6x139.7
Center Bore77.8 mm
Fastener & ThreadM14x1.5Lug Nut • Conical 60°
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 6x139.7 bolt pattern and 77.8 mm hub bore.

✓ No Centering Rings Required
2022-202677.8 mm CB
Jeep Wagoneer
Torque: 130 ft-lbsSpecs →
2021-202477.8 mm CB
Nissan Armada
Torque: 130 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Within Normal ToleranceDiameter: +0.63" (+1.98%)
+1.98%
Original Baseline Tire275/65R18
New Target Tire285/70R17
QUICK SIZES:
32.1"32.7"
Speedometer Variance Table
30 mph gauge30.6 actual+0.6 mph
45 mph gauge45.9 actual+0.9 mph
60 mph gauge61.2 actual+1.2 mph
70 mph gauge71.4 actual+1.4 mph
80 mph gauge81.6 actual+1.6 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
265/70R17
Mounted on 17x7.0" Wheel
PCD: 6x139.7
Center Bore: 77.8 mm
🛡️ Technical Benefits for 2019 Ram 1500
⛷️ Higher Ground Pressure
A narrower tire (265mm vs 275mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Drive-Cycle
Relearn Sequence0 / 3 Steps Complete
1
Set all cold tire pressures to placard specification
2
Drive vehicle above 15 mph for at least 15 minutes
3
Cluster updates sensor IDs
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →

🔍 Pre-Purchase Fitment & Chassis Inspection Checklist

Universal 8-Point Buyer Guide →

✓ Wheel Hub & Bearing Inspection

  • • Inspect 77.8mm hub center bore for rust scale.
  • • Verify 6-lug pattern (2019+ DT uses 6-lug, 2018 DS used 5-lug).

✓ Suspension & Steering Clearance

  • • Check rear coil spring or air suspension bellow integrity.
  • • Inspect upper control arm ball joints for play.
Brake Caliper Clearance Note

18-inch minimum wheel diameter required to clear heavy-duty front dual-piston calipers.

Common Wear Replacement Parts

📋 One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

🔩

Verified Hardware & Installation Kit for 2019 1500

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2019 Ram 1500)

8 Verified Q&As
Q What is the bolt pattern for a 2019 Ram 1500?
The factory bolt pattern (PCD) for the 2019 Ram 1500 is 6x139.7 (6-lug configuration) with a pitch circle diameter of 139.7 mm. Center bore hub diameter is 77.8 mm.
Q What is the wheel lug torque specification for a 2019 Ram 1500?
The official factory wheel lug torque specification for the 2019 Ram 1500 is 130 ft-lbs (176 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2019 Ram 1500?
The official maximum braked towing capacity for the 2019 Ram 1500 is 1,000 lbs (454 kg) with a maximum tongue weight limit of 100 lbs. Recommended hitch receiver: Class I (1.25-inch Receiver). Unbraked trailer limit is 350 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2019 Ram 1500?
Factory stock tire sizing for the 2019 Ram 1500 is 275/65R18 with a recommended cold tire pressure of 36 PSI front and 36 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2019 Ram 1500 and are hub centric rings needed?
The center bore diameter is exactly 77.8 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 77.8mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2019 Ram 1500 use?
The 2019 Ram 1500 utilizes M14x1.5 Lug Nuts with a Conical 60° seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2019 Ram 1500 have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Drive-Cycle: Set all cold tire pressures to placard specification
Q What aftermarket wheel offset and tire sizes fit a 2019 Ram 1500 without rubbing?
For an aggressive yet flush aesthetic without fender rolling or rubbing, the recommended setup is 20x9.0 ET+0 wheels with 33x12.50R20 tires. For a 100% rub-free conservative upgrade, choose 20x9.0 ET+18 with 275/55R20. Factory safe offset range spans +10mm to +35mm.