2025 Toyota 4Runner
Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.
2025 Toyota 4Runner Towing Capacity & Hitch Telemetry
Official manufacturer braked tow ratings, max tongue weight, and payload limits.
TNGA-F body-on-frame architecture rated up to 6,000 lbs braked towing across properly equipped 6th-gen i-FORCE and i-FORCE MAX models. Verify exact door-jamb GVWR/GCWR before loading.
- • Unbraked trailer maximum limit: 1500 lbs (680 kg).
- • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
- • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.
2025 Toyota 4Runner Quick Fitment Answers
Looking for exact hub and wheel specifications for the 2025 Toyota 4Runner? The factory bolt pattern is 6x139.7 (6-lug) with a 95.1 mm center bore. The manufacturer specified wheel lug torque is 97 ft-lbs (131 Nm) using M14x1.5 Lug Nuts with a Flat / Mag Seat with Washer (OEM Alloy) seating surface. Safe wheel offset range is +20mm to +55mm.
Factory OEM Wheel & Tire Configurations (2025)
4 TRIM OPTIONS| Trim Name | Wheel Size | Tire Specification | Placard PSI | Equipment |
|---|---|---|---|---|
| SR5 (17" Dark Gray Metallic Alloy) | 17x7.5 ET+55 | 265/70R17
Compare ⚡
| 35 / 35 PSI | Find Tires → |
| TRD Off-Road / Off-Road Premium (18" Machined Alloy) | 18x7.5 ET+55 | 265/70R18
Compare ⚡
| 35 / 35 PSI | Find Tires → |
| TRD Sport / Limited / Platinum (20" Alloy) | 20x8 ET+55 | 265/60R20
Compare ⚡
| 35 / 35 PSI | Find Tires → |
| TRD Pro / Trailhunter (18" Wide-Track Heritage Alloy) | 18x8.5 ET+20 | 265/70R18
Compare ⚡
| 36 / 36 PSI | Find Tires → |
🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues
2 DOCUMENTED ISSUESLegacy 5th-gen 4Runner wheels (106.1mm bore, M12 holes) vibrating or failing to seat flush on N380 hubs
6th-gen N380 shifted from 106.1mm bore / M12x1.5 to 95.1mm hub bore / M14x1.5 studs, requiring hub-centric rings and M14-compatible lug seats.
Under- or over-torqued lug nuts after wheel swaps
Factory aluminum alloy wheels specify 97 ft-lbs (131 Nm), whereas optional steel spare/utility wheels require higher clamp torque (154 ft-lbs / 209 Nm).
Hub Centric Ring Finder & Vibration Eliminator
Precision adapter sizing for Toyota 4Runner factory 95.1 mm hub snout.
The wheel bore (73.1 mm) is smaller than the car hub (95.1 mm). The wheel will NOT physically seat flush on the hub face without wheel spacers or center-bore machining.
OEM vs. Aftermarket Visual Stance & Poke Gauge
Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.
Printable Mechanic Spec Card & Torque Sequence
High-contrast pocket card for tire shops, track days, and garage toolboxes.
2025 Toyota 4Runner
fitmentspec.com/toyota/4runner/2025Cross-Vehicle OEM Wheel Swap Compatibility (6x139.7)
Verified OEM donor vehicles whose factory wheels fit the Toyota 4Runner hub (95.1mm).

Cadillac Escalade
Chevrolet Colorado

Chevrolet Silverado 1500

Chevrolet Silverado 1500

Chevrolet Suburban

Chevrolet Tahoe

Ford Bronco
Ford Bronco Raptor
⚡ Will It Rub? 2D Offset & Strut Clearance
Real-time inner strut clearance and outer fender poke calculation.
WINTER WHEEL & MINUS-SIZING ADVISOR
Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.
📡 TPMS Protocol & Relearn Procedure
US OEM Sensor Protocol & Step-by-Step Calibration
🔍 Pre-Purchase Fitment & Chassis Inspection Checklist
Universal 8-Point Buyer Guide →✓ Wheel Hub & Bearing Inspection
- • Verify wheel center bore is 95.1mm hub-centric (or fitted with precision 106.1-to-95.1mm metal rings on aftermarket wheels) and confirm M14x1.5 lug torque at 97 ft-lbs (131 Nm).
- • Check front hub assemblies for play or noise if oversized 33–35" tires and zero/negative-offset wheels were previously installed.
✓ Suspension & Steering Clearance
- • Test Stabilizer Disconnect Mechanism (SDM) operation on TRD Pro / Trailhunter trims and inspect front upper control arm ball joints for clearance against high-offset (+55mm) wheels.
- • Inspect underbody skid plates and front air dam / crash-bar brackets for off-road impact or modification.
Factory 17x7.5 ET55 wheels clear standard TNGA-F brakes; verify spoke and barrel clearance before installing 17-inch aftermarket wheels with high positive offsets.
📋 One-Click Forum Spec Exporter
Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).