FitmentSpec Logo
Toyota logo
6th Gen (N380 TNGA-F Platform) (2025–2026)

2026 Toyota 4Runner

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2026 Toyota 4Runner
Factory Powertrain i-FORCE 2.4L Turbo I4 (278 HP) / i-FORCE MAX 2.4L Hybrid (326 HP)
326 HP (243 kW) 465 lb-ft 2.4L Inline-4 Turbo Hybrid
Chassis Dimensions Exterior & Curb Weight
L: 194.9" W: 78" WB: 112.2" 4,610 – 5,500 lbs lbs
Center BoreHub Centric
95.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+20 to +55
Flush Target: ET +20
Lug TorqueM14x1.5
97 ft-lbs
131 Nm • Flat Seat
Fastener: Flat / Mag Seat with Washer (OEM Alloy) Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2026 Toyota 4Runner Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 6,000 lbs
Max Towing (Braked)
6,000 lbs
2,722 kg
With factory trailer brakes
Max Payload Capacity
1,700 lbs
771 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
600 lbs
272 kg
Maximum hitch downward load
Hitch Receiver Class
Class IV (Integrated 2-inch Receiver)
Weight distribution rated
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2026 4Runner
Selected Load: 6,000 lbs • Vehicle Rating: 6,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

TNGA-F body-on-frame architecture rated up to 6,000 lbs braked towing across properly equipped 6th-gen i-FORCE and i-FORCE MAX models. Verify exact door-jamb GVWR/GCWR before loading.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 1500 lbs (680 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2026 Toyota 4Runner Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2026 Toyota 4Runner? The factory bolt pattern is 6x139.7 (6-lug) with a 95.1 mm center bore. The manufacturer specified wheel lug torque is 97 ft-lbs (131 Nm) using M14x1.5 Lug Nuts with a Flat / Mag Seat with Washer (OEM Alloy) seating surface. Safe wheel offset range is +20mm to +55mm.

Factory OEM Wheel & Tire Configurations (2026)

4 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
SR5 (17" Dark Gray Metallic Alloy) 17x7.5 ET+55
265/70R17 Compare ⚡
35 / 35 PSI Find Tires →
TRD Off-Road / Off-Road Premium (18" Machined Alloy) 18x7.5 ET+55
265/70R18 Compare ⚡
35 / 35 PSI Find Tires →
TRD Sport / Limited / Platinum (20" Alloy) 20x8 ET+55
265/60R20 Compare ⚡
35 / 35 PSI Find Tires →
TRD Pro / Trailhunter (18" Wide-Track Heritage Alloy) 18x8.5 ET+20
265/70R18 Compare ⚡
36 / 36 PSI Find Tires →

🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues

2 DOCUMENTED ISSUES
TNGA-F Hub Bore & M14 Stud Backward Compatibility High Severity
Symptom

Legacy 5th-gen 4Runner wheels (106.1mm bore, M12 holes) vibrating or failing to seat flush on N380 hubs

Root Cause & TSB Details

6th-gen N380 shifted from 106.1mm bore / M12x1.5 to 95.1mm hub bore / M14x1.5 studs, requiring hub-centric rings and M14-compatible lug seats.

Affected Components: 95.1mm Wheel Hub SpigotM14x1.5 Wheel Studs
Aluminum vs. Steel Wheel Lug Torque Discrepancy Moderate Severity
Symptom

Under- or over-torqued lug nuts after wheel swaps

Root Cause & TSB Details

Factory aluminum alloy wheels specify 97 ft-lbs (131 Nm), whereas optional steel spare/utility wheels require higher clamp torque (154 ft-lbs / 209 Nm).

Affected Components: OEM Mag-Seat Lug NutsWheel Studs
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Toyota 4Runner factory 95.1 mm hub snout.

Factory Hub: 95.1mm
Hub Diagnostic Result
🚨 INCOMPATIBLE WHEEL BORE (TOO SMALL)

The wheel bore (73.1 mm) is smaller than the car hub (95.1 mm). The wheel will NOT physically seat flush on the hub face without wheel spacers or center-bore machining.

💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 7.5" ET55
New Wheel Width:8.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET45 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

6x139.7
2025-2026 FITMENT SPECIFICATION

2026 Toyota 4Runner

fitmentspec.com/toyota/4runner/2026
FINAL TORQUE97 ft-lbs(131 Nm)
Bolt Pattern (PCD)6x139.7
Center Bore95.1 mm
Fastener & ThreadM14x1.5Lug Nut • Flat / Mag Seat with Washer (OEM Alloy)
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Significant DifferenceDiameter: +1.10" (+3.49%)
+3.49%
Original Baseline Tire265/70R17
New Target Tire285/70R17
QUICK SIZES:
31.6"32.7"
Speedometer Variance Table
30 mph gauge31.0 actual+1.0 mph
45 mph gauge46.6 actual+1.6 mph
60 mph gauge62.1 actual+2.1 mph
70 mph gauge72.4 actual+2.4 mph
80 mph gauge82.8 actual+2.8 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
255/75R16
Mounted on 16x6.5" Wheel
PCD: 6x139.7
Center Bore: 95.1 mm
🛡️ Technical Benefits for 2026 Toyota 4Runner
⛷️ Higher Ground Pressure
A narrower tire (255mm vs 265mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
42607-48020
Relearn Protocol
Auto-Relearn
Relearn Sequence0 / 3 Steps Complete
1
Inflate all four tires (plus spare if equipped with TPMS) to cold door-jamb pressure (35–36 PSI).
2
Cycle ignition ON and open Vehicle Settings > Tire Pressure System > Register / Calibrate on the Toyota Audio Multimedia display.
3
Drive above 19 mph (30 km/h) for 10 to 15 minutes until all wheel pressures populate.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →

🔍 Pre-Purchase Fitment & Chassis Inspection Checklist

Universal 8-Point Buyer Guide →

✓ Wheel Hub & Bearing Inspection

  • • Verify wheel center bore is 95.1mm hub-centric (or fitted with precision 106.1-to-95.1mm metal rings on aftermarket wheels) and confirm M14x1.5 lug torque at 97 ft-lbs (131 Nm).
  • • Check front hub assemblies for play or noise if oversized 33–35" tires and zero/negative-offset wheels were previously installed.

✓ Suspension & Steering Clearance

  • • Test Stabilizer Disconnect Mechanism (SDM) operation on TRD Pro / Trailhunter trims and inspect front upper control arm ball joints for clearance against high-offset (+55mm) wheels.
  • • Inspect underbody skid plates and front air dam / crash-bar brackets for off-road impact or modification.
Brake Caliper Clearance Note

Factory 17x7.5 ET55 wheels clear standard TNGA-F brakes; verify spoke and barrel clearance before installing 17-inch aftermarket wheels with high positive offsets.

Common Wear Replacement Parts

📋 One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

🔩

Verified Hardware & Installation Kit for 2026 4Runner

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2026 Toyota 4Runner)

8 Verified Q&As
Q What is the bolt pattern for a 2026 Toyota 4Runner?
The factory bolt pattern (PCD) for the 2026 Toyota 4Runner is 6x139.7 (6-lug configuration) with a pitch circle diameter of 139.7 mm. Center bore hub diameter is 95.1 mm.
Q What is the wheel lug torque specification for a 2026 Toyota 4Runner?
The official factory wheel lug torque specification for the 2026 Toyota 4Runner is 97 ft-lbs (131 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2026 Toyota 4Runner?
The official maximum braked towing capacity for the 2026 Toyota 4Runner is 6,000 lbs (2,722 kg) with a maximum tongue weight limit of 600 lbs. Recommended hitch receiver: Class IV (Integrated 2-inch Receiver). Unbraked trailer limit is 1,500 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2026 Toyota 4Runner?
Factory stock tire sizing for the 2026 Toyota 4Runner is 265/70R17 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2026 Toyota 4Runner and are hub centric rings needed?
The center bore diameter is exactly 95.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 95.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2026 Toyota 4Runner use?
The 2026 Toyota 4Runner utilizes M14x1.5 Lug Nuts with a Flat / Mag Seat with Washer (OEM Alloy) seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2026 Toyota 4Runner have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Auto-Relearn: Inflate all four tires (plus spare if equipped with TPMS) to cold door-jamb pressure (35–36 PSI).
Q What aftermarket wheel offset and tire sizes fit a 2026 Toyota 4Runner without rubbing?
For an aggressive yet flush aesthetic without fender rolling or rubbing, the recommended setup is 17x8.5 ET+20 wheels with 285/70R17 tires. For a 100% rub-free conservative upgrade, choose 17x8.0 ET+35 with 265/70R17. Factory safe offset range spans +20mm to +55mm.