FitmentSpec Logo
Toyota logo
8th Gen AN120/AN130 (Single / Extra / Double Cab - SR / SR5 / Invincible) (2016–2026)

2019 Toyota Hilux

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2019 Toyota Hilux
Factory Powertrain 2.8L 1GD-FTV D-4D Common Rail Turbo Diesel
201 HP (150 kW) 369 lb-ft 2.8L Inline-4 Diesel
Chassis Dimensions Exterior & Curb Weight
L: 209.6" W: 73" WB: 121.5" 4,300 – 4,630 lbs lbs
Center BoreHub Centric
106.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+15 to +35
Flush Target: ET +20
Lug TorqueM12x1.5
80 ft-lbs
108 Nm • Mag Seat
Fastener: Mag Seat with Flat Washer (OEM Alloy) / 60° Conical (OEM Steel & Aftermarket) Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2019 Toyota Hilux Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 7,700 lbs
Max Towing (Braked)
7,700 lbs
3,500 kg
With factory trailer brakes
Max Payload Capacity
2,240 lbs
1,016 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
770 lbs
349 kg
Maximum hitch downward load
Hitch Receiver Class
Class IV (2.0-inch Heavy Duty Receiver)
Weight distribution rated
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2019 Hilux
Selected Load: 7,700 lbs • Vehicle Rating: 7,700 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Legendary commercial towing platform rated for full 3,500 kg (7,700 lbs) braked towing. Electric trailer brake controller required above 750 kg unbraked.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 1650 lbs (750 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2019 Toyota Hilux Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2019 Toyota Hilux? The factory bolt pattern is 6x139.7 (6-lug) with a 106.1 mm center bore. The manufacturer specified wheel lug torque is 80 ft-lbs (108 Nm) using M12x1.5 Lug Nuts with a Mag Seat with Flat Washer (OEM Alloy) / 60° Conical (OEM Steel & Aftermarket) seating surface. Safe wheel offset range is +15mm to +35mm.

Factory OEM Wheel & Tire Configurations (2019)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
17" SR / Workmate / Invincible Alloy 17x7.5 ET+30
265/65R17 Compare ⚡
29 / 32 PSI Find Tires →
18" SR5 / Invincible X / Rogue Alloy 18x7.5 ET+30
265/60R18 Compare ⚡
29 / 32 PSI Find Tires →

🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues

2 DOCUMENTED ISSUES
Wheel Lug Fasteners & Seat Interface Critical Severity
Symptom

Wheel vibration or loosening after installing aftermarket wheels with factory lug nuts

Root Cause & TSB Details

Improper seat contact: factory Toyota alloy wheels require Mag-style flat-washer shank lug nuts, whereas aftermarket wheels require 60-degree conical taper lug nuts

Affected Components: OEM Mag Washer Lug NutsWheel Stud ThreadsWheel Hub Flange
Rear Leaf Spring Suspension Low Severity
Symptom

High-pitched squeaking or binding from rear axle over speed bumps and dirt trails

Root Cause & TSB Details

Dust and grit intrusion between leaf spring friction separator pads and dry shackle polyurethane/rubber bushings

Affected Components: Rear Leaf Spring Separator PadsRear Leaf Shackle BushingsU-Bolt Clamps
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Toyota Hilux factory 106.1 mm hub snout.

Factory Hub: 106.1mm
Hub Diagnostic Result
🚨 INCOMPATIBLE WHEEL BORE (TOO SMALL)

The wheel bore (73.1 mm) is smaller than the car hub (106.1 mm). The wheel will NOT physically seat flush on the hub face without wheel spacers or center-bore machining.

💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 7.5" ET30
New Wheel Width:8.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET20 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

6x139.7
2016-2026 FITMENT SPECIFICATION

2019 Toyota Hilux

fitmentspec.com/toyota/hilux/2019
FINAL TORQUE80 ft-lbs(108 Nm)
Bolt Pattern (PCD)6x139.7
Center Bore106.1 mm
Fastener & ThreadM12x1.5Lug Nut • Mag Seat with Flat Washer (OEM Alloy) / 60° Conical (OEM Steel & Aftermarket)
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +2.15" (+7.02%)
+7.02%
Original Baseline Tire265/65R17
New Target Tire285/70R17
QUICK SIZES:
30.6"32.7"
Speedometer Variance Table
30 mph gauge32.1 actual+2.1 mph
45 mph gauge48.2 actual+3.2 mph
60 mph gauge64.2 actual+4.2 mph
70 mph gauge74.9 actual+4.9 mph
80 mph gauge85.6 actual+5.6 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
255/70R16
Mounted on 16x6.5" Wheel
PCD: 6x139.7
Center Bore: 106.1 mm
🛡️ Technical Benefits for 2019 Toyota Hilux
⛷️ Higher Ground Pressure
A narrower tire (255mm vs 265mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS433 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
42607-02031 / 42607-30060
Relearn Protocol
Cluster-Reset
Relearn Sequence0 / 4 Steps Complete
1
Park vehicle safely, set parking brake, and inflate cold tires to door placard pressure (note higher rear spec when loaded).
2
Turn ignition switch ON without starting engine.
3
Press and hold TPMS Set switch (under instrument panel or in vehicle multi-information display) until warning light flashes 3 times slowly.
4
Wait 3 minutes, then drive vehicle at 25 mph (40 km/h) or faster for 20 minutes to complete sensor ID calibration.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →

🔍 Pre-Purchase Fitment & Chassis Inspection Checklist

Universal 8-Point Buyer Guide →

✓ Wheel Hub & Bearing Inspection

  • • Inspect massive 106.1mm hub register for corrosion and ensure wheels seat perfectly flush on hub face.
  • • Verify lug nut seat type: strictly verify Mag-style shank nuts with captive flat washers are used ONLY on OEM alloy wheels. For OEM steel wheels, torque to 112 ft-lbs (152 Nm); for OEM alloys, torque to 80 ft-lbs (108 Nm).

✓ Suspension & Steering Clearance

  • • Check clearance between upper control arm (UCA) ball joint and inner tire sidewall with tires wider than 265mm.
  • • Inspect front body mount cab clearance at full steering lock when running 33-inch or larger tires.
Brake Caliper Clearance Note

Hilux 4-piston front brake calipers require 17-inch minimum wheel diameter on 2016+ models; 16-inch wheels will contact outer caliper body on 2.8L models.

Common Wear Replacement Parts

📋 One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

🔩

Verified Hardware & Installation Kit for 2019 Hilux

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2019 Toyota Hilux)

8 Verified Q&As
Q What is the bolt pattern for a 2019 Toyota Hilux?
The factory bolt pattern (PCD) for the 2019 Toyota Hilux is 6x139.7 (6-lug configuration) with a pitch circle diameter of 139.7 mm. Center bore hub diameter is 106.1 mm.
Q What is the wheel lug torque specification for a 2019 Toyota Hilux?
The official factory wheel lug torque specification for the 2019 Toyota Hilux is 80 ft-lbs (108 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2019 Toyota Hilux?
The official maximum braked towing capacity for the 2019 Toyota Hilux is 7,700 lbs (3,500 kg) with a maximum tongue weight limit of 770 lbs. Recommended hitch receiver: Class IV (2.0-inch Heavy Duty Receiver). Unbraked trailer limit is 1,650 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2019 Toyota Hilux?
Factory stock tire sizing for the 2019 Toyota Hilux is 265/65R17 with a recommended cold tire pressure of 29 PSI front and 32 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2019 Toyota Hilux and are hub centric rings needed?
The center bore diameter is exactly 106.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 106.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2019 Toyota Hilux use?
The 2019 Toyota Hilux utilizes M12x1.5 Lug Nuts with a Mag Seat with Flat Washer (OEM Alloy) / 60° Conical (OEM Steel & Aftermarket) seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2019 Toyota Hilux have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 433 MHz. The relearn protocol is Cluster-Reset: Park vehicle safely, set parking brake, and inflate cold tires to door placard pressure (note higher rear spec when loaded).
Q What aftermarket wheel offset and tire sizes fit a 2019 Toyota Hilux without rubbing?
For an aggressive yet flush aesthetic without fender rolling or rubbing, the recommended setup is 17x8.5 ET20 wheels with 265/70R17 tires. For a 100% rub-free conservative upgrade, choose 17x8.0 ET25 with 265/65R17. Factory safe offset range spans +15mm to +35mm.