2021 Toyota Hilux
Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.
2021 Toyota Hilux Towing Capacity & Hitch Telemetry
Official manufacturer braked tow ratings, max tongue weight, and payload limits.
Legendary commercial towing platform rated for full 3,500 kg (7,700 lbs) braked towing. Electric trailer brake controller required above 750 kg unbraked.
- • Unbraked trailer maximum limit: 1650 lbs (750 kg).
- • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
- • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.
2021 Toyota Hilux Quick Fitment Answers
Looking for exact hub and wheel specifications for the 2021 Toyota Hilux? The factory bolt pattern is 6x139.7 (6-lug) with a 106.1 mm center bore. The manufacturer specified wheel lug torque is 80 ft-lbs (108 Nm) using M12x1.5 Lug Nuts with a Mag Seat with Flat Washer (OEM Alloy) / 60° Conical (OEM Steel & Aftermarket) seating surface. Safe wheel offset range is +15mm to +35mm.
Factory OEM Wheel & Tire Configurations (2021)
2 TRIM OPTIONS| Trim Name | Wheel Size | Tire Specification | Placard PSI | Equipment |
|---|---|---|---|---|
| 17" SR / Workmate / Invincible Alloy | 17x7.5 ET+30 | 265/65R17
Compare ⚡
| 29 / 32 PSI | Find Tires → |
| 18" SR5 / Invincible X / Rogue Alloy | 18x7.5 ET+30 | 265/60R18
Compare ⚡
| 29 / 32 PSI | Find Tires → |
🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues
2 DOCUMENTED ISSUESWheel vibration or loosening after installing aftermarket wheels with factory lug nuts
Improper seat contact: factory Toyota alloy wheels require Mag-style flat-washer shank lug nuts, whereas aftermarket wheels require 60-degree conical taper lug nuts
High-pitched squeaking or binding from rear axle over speed bumps and dirt trails
Dust and grit intrusion between leaf spring friction separator pads and dry shackle polyurethane/rubber bushings
Hub Centric Ring Finder & Vibration Eliminator
Precision adapter sizing for Toyota Hilux factory 106.1 mm hub snout.
The wheel bore (73.1 mm) is smaller than the car hub (106.1 mm). The wheel will NOT physically seat flush on the hub face without wheel spacers or center-bore machining.
OEM vs. Aftermarket Visual Stance & Poke Gauge
Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.
Printable Mechanic Spec Card & Torque Sequence
High-contrast pocket card for tire shops, track days, and garage toolboxes.
2021 Toyota Hilux
fitmentspec.com/toyota/hilux/2021⚡ Will It Rub? 2D Offset & Strut Clearance
Real-time inner strut clearance and outer fender poke calculation.
WINTER WHEEL & MINUS-SIZING ADVISOR
Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.
📡 TPMS Protocol & Relearn Procedure
US OEM Sensor Protocol & Step-by-Step Calibration
🔍 Pre-Purchase Fitment & Chassis Inspection Checklist
Universal 8-Point Buyer Guide →✓ Wheel Hub & Bearing Inspection
- • Inspect massive 106.1mm hub register for corrosion and ensure wheels seat perfectly flush on hub face.
- • Verify lug nut seat type: strictly verify Mag-style shank nuts with captive flat washers are used ONLY on OEM alloy wheels. For OEM steel wheels, torque to 112 ft-lbs (152 Nm); for OEM alloys, torque to 80 ft-lbs (108 Nm).
✓ Suspension & Steering Clearance
- • Check clearance between upper control arm (UCA) ball joint and inner tire sidewall with tires wider than 265mm.
- • Inspect front body mount cab clearance at full steering lock when running 33-inch or larger tires.
Hilux 4-piston front brake calipers require 17-inch minimum wheel diameter on 2016+ models; 16-inch wheels will contact outer caliper body on 2.8L models.
📋 One-Click Forum Spec Exporter
Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).
Verified Hardware & Installation Kit for 2021 Hilux
Mag Seat with Flat Washer (OEM Alloy) / 60° Conical (OEM Steel & Aftermarket) seating
Eliminates wheel vibration
1/2" drive click wrench