FitmentSpec Logo
Honda logo
11th Gen (CY) (2023–2026)

2024 Honda Accord

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2024 Honda Accord
Factory Powertrain 1.5L Turbo VTEC / 2.0L 4-Cylinder Two-Motor Hybrid
204 HP 247 lb-ft
Chassis Dimensions Exterior & Curb Weight
WB: 111.4" 3,477 - 3,530 lbs lbs
Center BoreHub Centric
64.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+38 to +50
Flush Target: ET +35
Lug TorqueM12 x 1.5
80 ft-lbs
108 Nm • Ball Seat
Fastener: Ball / Radius Seat (OEM) Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2024 Honda Accord Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 1,000 lbs
Max Towing (Braked)
1,000 lbs
454 kg
With factory trailer brakes
Max Payload Capacity
1,050 lbs
476 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
100 lbs
45 kg
Maximum hitch downward load
Hitch Receiver Class
Class I (1.25-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2024 Accord
Selected Load: 1,000 lbs • Vehicle Rating: 1,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

1,000 lbs capacity on 1.5L Turbo gas models. American Honda does not recommend trailer towing for Accord Hybrid.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 350 lbs (159 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2024 Honda Accord Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2024 Honda Accord? The factory bolt pattern is 5x114.3 (5-lug) with a 64.1 mm center bore. The manufacturer specified wheel lug torque is 80 ft-lbs (108 Nm) using M12 x 1.5 Lug Nuts with a Ball / Radius Seat (OEM) seating surface. Safe wheel offset range is +38mm to +50mm.

PCD: 5x114.3 → Center Bore: 64.1 mm → Torque: 80 ft-lbs → Fastener: M12 x 1.5 → Spacer Fit: ET+38 → Donor Wheel Swap → TPMS: Indirect (i-TPMS) (N/A (ABS Sensor Wheel-Speed Calculated) MHz) Engine: 204 HP

Factory OEM Wheel & Tire Configurations (2024)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
LX / EX 17x7.5 ET45
225/50R17 Compare ⚡
32-35 PSI Placard Find Tires →
Sport / EX-L / Sport-L / Touring Hybrid 19x8.5 ET50
235/40R19 Compare ⚡
32-35 PSI Placard Find Tires →
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Honda Accord factory 64.1 mm hub snout.

Factory Hub: 64.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +9.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 64.1mm (OD: 73.1mm / ID: 64.1mm)
🛒 Order 73.1mm to 64.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 7.5" ET45
New Wheel Width:8.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET35 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x114.3
2023-2026 FITMENT SPECIFICATION

2024 Honda Accord

fitmentspec.com/honda/accord/2024
FINAL TORQUE80 ft-lbs(108 Nm)
Bolt Pattern (PCD)5x114.3
Center Bore64.1 mm
Fastener & ThreadM12 x 1.5Lug Nut • Ball / Radius Seat (OEM)
TPMS CalibrationIndirect (i-TPMS)Door Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x114.3 bolt pattern and 64.1 mm hub bore.

✓ No Centering Rings Required
2013-202264.1 mm CB
Acura ILX
Torque: 80 ft-lbsSpecs →
2023-202664.1 mm CB
Acura Integra
Torque: 80 ft-lbsSpecs →
2019-202664.1 mm CB
Acura RDX
Torque: 80 ft-lbsSpecs →
2002-200664.1 mm CB
Acura RSX
Torque: 80 ft-lbsSpecs →
2004-201464.1 mm CB
Acura TSX
Torque: 80 ft-lbsSpecs →
2022-202664.1 mm CB
Honda Civic
Torque: 80 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +6.85" (+26.49%)
+26.49%
Original Baseline Tire225/50R17
New Target Tire285/70R17
QUICK SIZES:
25.9"32.7"
Speedometer Variance Table
30 mph gauge37.9 actual+7.9 mph
45 mph gauge56.9 actual+11.9 mph
60 mph gauge75.9 actual+15.9 mph
70 mph gauge88.5 actual+18.5 mph
80 mph gauge101.2 actual+21.2 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
215/55R16
Mounted on 16x6.5" Wheel
PCD: 5x114.3
Center Bore: 64.1 mm
🛡️ Technical Benefits for 2024 Honda Accord
⛷️ Higher Ground Pressure
A narrower tire (215mm vs 225mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

INDIRECT (I-TPMS) TPMSN/A (ABS Sensor Wheel-Speed Calculated) MHz
Architecture
Indirect Wheel Speed ABS
Sensor Part Number
OEM Indirect Calibrated
Relearn Protocol
Drive Relearn
Relearn Sequence0 / 1 Steps Complete
1
Inflate all four cold tires to the factory recommended placard pressure (33 PSI).Shift vehicle into PARK and set the electronic parking brake.Turn the ignition switch or power mode to ON (ENGINE READY).On the central 12.3-inch Honda touchscreen, tap Settings -> Vehicle.Scroll down and select 'TPMS Calibration'.Tap 'Calibrate'. The tire pressure warning indicator light will blink twice, confirming calibration has begun.Drive the vehicle between 30 mph and 65 mph for approximately 20-30 minutes to complete the dynamic learning cycle.
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →

📋 One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

🔩

Verified Hardware & Installation Kit for 2024 Accord

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2024 Honda Accord)

8 Verified Q&As
Q What is the bolt pattern for a 2024 Honda Accord?
The factory bolt pattern (PCD) for the 2024 Honda Accord is 5x114.3 (5-lug configuration) with a pitch circle diameter of 114.3 mm. Center bore hub diameter is 64.1 mm.
Q What is the wheel lug torque specification for a 2024 Honda Accord?
The official factory wheel lug torque specification for the 2024 Honda Accord is 80 ft-lbs (108 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2024 Honda Accord?
The official maximum braked towing capacity for the 2024 Honda Accord is 1,000 lbs (454 kg) with a maximum tongue weight limit of 100 lbs. Recommended hitch receiver: Class I (1.25-inch Receiver). Unbraked trailer limit is 350 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2024 Honda Accord?
Factory stock tire sizing for the 2024 Honda Accord is 225/50R17 with a recommended cold tire pressure of 35 PSI front and 35 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2024 Honda Accord and are hub centric rings needed?
The center bore diameter is exactly 64.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 64.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2024 Honda Accord use?
The 2024 Honda Accord utilizes M12 x 1.5 Lug Nuts with a Ball / Radius Seat (OEM) seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2024 Honda Accord have Direct or Indirect TPMS and how is it reset?
This vehicle utilizes standard valve stems without requiring active electronic TPMS sensor recalibration.
Q What aftermarket wheel offset and tire sizes fit a 2024 Honda Accord without rubbing?
For a flush aftermarket stance without rubbing or cutting, maintain wheel offsets between +38mm and +50mm with a flush target of ET +35. Always test clearance at full steering lock.