FitmentSpec Logo
Honda logo
6th Gen (RS) (2023–2026)

2026 Honda CR-V

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2026 Honda CR-V
Factory Powertrain 2.0L 4-Cylinder Atkinson Cycle + Two-Motor Hybrid
204 HP (152 kW) 247 lb-ft 2.0L Inline-4
Chassis Dimensions Exterior & Curb Weight
L: 184.8" W: 73.5" WB: 106.3" 3,472 – 3,926 lbs lbs
Center BoreHub Centric
64.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+38 to +50
Flush Target: ET +40
Lug TorqueM12x1.5
80 ft-lbs
108 Nm • Conical Seat
Fastener: Conical 60° Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2026 Honda CR-V Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 1,500 lbs
Max Towing (Braked)
1,500 lbs
680 kg
With factory trailer brakes
Max Payload Capacity
1,100 lbs
499 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
150 lbs
68 kg
Maximum hitch downward load
Hitch Receiver Class
Class I/II (1.25-inch Receiver)
Standard bumper / ball mount
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2026 CR-V
Selected Load: 1,500 lbs • Vehicle Rating: 1,500 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

1,500 lbs towing on 1.5L Turbo gas models (1,000 lbs on Sport Hybrid). Best suited for lightweight utility trailers and hitch-mounted bike racks/cargo boxes.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 525 lbs (238 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2026 Honda CR-V Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2026 Honda CR-V? The factory bolt pattern is 5x114.3 (5-lug) with a 64.1 mm center bore. The manufacturer specified wheel lug torque is 80 ft-lbs (108 Nm) using M12x1.5 Lug Nuts with a Conical 60° seating surface. Safe wheel offset range is +38mm to +50mm.

Factory OEM Wheel & Tire Configurations (2026)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
EX / Sport Hybrid 18x7.5 ET+45
235/60R18 Compare ⚡
33 / 33 PSI Find Tires →
Sport Touring Hybrid 19x7.5 ET+45
235/55R19 Compare ⚡
33 / 33 PSI Find Tires →

🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues

1 DOCUMENTED ISSUES
Electric Power Steering Gearbox Sticky Sensation Moderate Severity
Symptom

Sticky, momentary resistance when making subtle steering corrections at highway speeds (50-70 mph)

Root Cause & TSB Details

Improper grease distribution in the steering gearbox worm wheel assembly (Honda TSB 23-037 / NHTSA Action)

Affected Components: Electric Power Steering GearboxEPS Worm Gear
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Honda CR-V factory 64.1 mm hub snout.

Factory Hub: 64.1mm
Hub Diagnostic Result
✅ HUB CENTRIC RINGS REQUIRED

The wheel bore is +9.0 mm larger than the vehicle hub. To prevent steering wheel wobble at 50–75 mph, install this exact ring set:

73.1mm to 64.1mm (OD: 73.1mm / ID: 64.1mm)
🛒 Order 73.1mm to 64.1mm Ring Set on Amazon↗
💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 7.5" ET45
New Wheel Width:8.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET35 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

5x114.3
2023-2026 FITMENT SPECIFICATION

2026 Honda CR-V

fitmentspec.com/honda/cr-v/2026
FINAL TORQUE80 ft-lbs(108 Nm)
Bolt Pattern (PCD)5x114.3
Center Bore64.1 mm
Fastener & ThreadM12x1.5Lug Nut • Conical 60°
TPMS CalibrationIndirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 5x114.3 bolt pattern and 64.1 mm hub bore.

✓ No Centering Rings Required
2013-202264.1 mm CB
Acura ILX
Torque: 80 ft-lbsSpecs →
2023-202664.1 mm CB
Acura Integra
Torque: 80 ft-lbsSpecs →
2019-202664.1 mm CB
Acura RDX
Torque: 80 ft-lbsSpecs →
2002-200664.1 mm CB
Acura RSX
Torque: 80 ft-lbsSpecs →
2004-201464.1 mm CB
Acura TSX
Torque: 80 ft-lbsSpecs →
2018-202264.1 mm CB
Honda Accord
Torque: 80 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Recalibrate RequiredDiameter: +3.61" (+12.39%)
+12.39%
Original Baseline Tire235/60R18
New Target Tire285/70R17
QUICK SIZES:
29.1"32.7"
Speedometer Variance Table
30 mph gauge33.7 actual+3.7 mph
45 mph gauge50.6 actual+5.6 mph
60 mph gauge67.4 actual+7.4 mph
70 mph gauge78.7 actual+8.7 mph
80 mph gauge89.9 actual+9.9 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
225/65R17
Mounted on 17x6.5" Wheel
PCD: 5x114.3
Center Bore: 64.1 mm
🛡️ Technical Benefits for 2026 Honda CR-V
⛷️ Higher Ground Pressure
A narrower tire (225mm vs 235mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

INDIRECT TPMSABS Wheel Speed Based
Architecture
Indirect Wheel Speed ABS
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Cluster-Reset
Relearn Sequence0 / 4 Steps Complete
1
Adjust tire pressure to placard value
2
Navigate to Vehicle Settings > TPMS Calibration on center touchscreen
3
Tap Calibrate
4
System automatically calibrates after 20 minutes of driving
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →

🔍 Pre-Purchase Fitment & Chassis Inspection Checklist

Universal 8-Point Buyer Guide →

✓ Wheel Hub & Bearing Inspection

  • • Verify 64.1mm hub faces are cleaned of corrosion during wheel swaps.
  • • Check wheel lug torque.

✓ Suspension & Steering Clearance

  • • Inspect front strut clearances with larger tire setups.
  • • Check rear independent multi-link trailing arms.
Brake Caliper Clearance Note

17-inch minimum rim diameter recommended to guarantee proper caliper clearance.

Common Wear Replacement Parts

📋 One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

🔩

Verified Hardware & Installation Kit for 2026 CR-V

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2026 Honda CR-V)

8 Verified Q&As
Q What is the bolt pattern for a 2026 Honda CR-V?
The factory bolt pattern (PCD) for the 2026 Honda CR-V is 5x114.3 (5-lug configuration) with a pitch circle diameter of 114.3 mm. Center bore hub diameter is 64.1 mm.
Q What is the wheel lug torque specification for a 2026 Honda CR-V?
The official factory wheel lug torque specification for the 2026 Honda CR-V is 80 ft-lbs (108 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2026 Honda CR-V?
The official maximum braked towing capacity for the 2026 Honda CR-V is 1,500 lbs (680 kg) with a maximum tongue weight limit of 150 lbs. Recommended hitch receiver: Class I/II (1.25-inch Receiver). Unbraked trailer limit is 525 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2026 Honda CR-V?
Factory stock tire sizing for the 2026 Honda CR-V is 235/60R18 with a recommended cold tire pressure of 33 PSI front and 33 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2026 Honda CR-V and are hub centric rings needed?
The center bore diameter is exactly 64.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 64.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2026 Honda CR-V use?
The 2026 Honda CR-V utilizes M12x1.5 Lug Nuts with a Conical 60° seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2026 Honda CR-V have Direct or Indirect TPMS and how is it reset?
It uses an Indirect TPMS system that calculates relative pressure by monitoring individual wheel rotation speeds via the ABS wheel speed sensors. Reset procedure: Cluster-Reset.
Q What aftermarket wheel offset and tire sizes fit a 2026 Honda CR-V without rubbing?
For an aggressive yet flush aesthetic without fender rolling or rubbing, the recommended setup is 19x8.5 ET+38 wheels with 245/50R19 tires. For a 100% rub-free conservative upgrade, choose 18x8.0 ET+40 with 235/60R18. Factory safe offset range spans +38mm to +50mm.