FitmentSpec Logo
Toyota logo
3rd Gen (XK70) (2022–2026)

2024 Toyota Tundra

Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.

2024 Toyota Tundra
Factory Powertrain 3.4L i-FORCE Twin-Turbocharged V6 (V35A-FTS)
389 HP (290 kW) 479 lb-ft 3.4L V6
Chassis Dimensions Exterior & Curb Weight
L: 233.6" W: 80.2" WB: 145.7" 5,380 – 6,185 lbs lbs
Center BoreHub Centric
95.1 mm
Hub Ring Spigot Diameter
Offset RangeET
+25 to +60
Flush Target: ET +35
Lug TorqueM14x1.5
97 ft-lbs
131 Nm • Conical Seat
Fastener: Conical 60° Lug Nut. Always re-torque after 50–100 miles of driving.Get Torque Wrench→
⚠️
Mandatory Verification Notice: Bolt patterns, hub tolerances, and torque values vary by factory brake option and trim. Always verify specs with your vehicle's driver door-jamb safety placard or a certified mechanic prior to mounting wheels. Use of this data is strictly at your own risk. Read Full Legal Disclaimer →
⚓

2024 Toyota Tundra Towing Capacity & Hitch Telemetry

Official manufacturer braked tow ratings, max tongue weight, and payload limits.

Certified Tow Rating: 12,000 lbs
Max Towing (Braked)
12,000 lbs
5,443 kg
With factory trailer brakes
Max Payload Capacity
1,940 lbs
880 kg
Cabin + bed passenger load
Max Tongue Weight (10%)
1,200 lbs
544 kg
Maximum hitch downward load
Hitch Receiver Class
Class IV (2-inch Receiver)
Weight distribution rated
🚛 Can It Tow? Real-World Trailer Capability Matcher
Click any trailer type to test compatibility against 2024 Tundra
Selected Load: 12,000 lbs • Vehicle Rating: 12,000 lbs
At Maximum Limit (Caution)
📋 Factory Towing Guidance:

Up to 12,000 lbs towing with i-FORCE 3.4L Twin-Turbo V6 and factory TOW/HAUL mode; i-FORCE MAX Hybrid rated up to 11,450 lbs.

⚙️ Essential Towing Safety Guidelines:
  • • Unbraked trailer maximum limit: 1500 lbs (680 kg).
  • • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
  • • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.

2024 Toyota Tundra Quick Fitment Answers

Looking for exact hub and wheel specifications for the 2024 Toyota Tundra? The factory bolt pattern is 6x139.7 (6-lug) with a 95.1 mm center bore. The manufacturer specified wheel lug torque is 97 ft-lbs (131 Nm) using M14x1.5 Lug Nuts with a Conical 60° seating surface. Safe wheel offset range is +25mm to +60mm.

Factory OEM Wheel & Tire Configurations (2024)

2 TRIM OPTIONS
Trim Name Wheel Size Tire Specification Placard PSI Equipment
SR / SR5 18x7.5 ET+60
265/70R18 Compare ⚡
36 / 36 PSI Find Tires →
Limited / TRD Off-Road 20x8 ET+60
265/60R20 Compare ⚡
36 / 36 PSI Find Tires →

🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues

1 DOCUMENTED ISSUES
Engine Main Crankshaft Bearing Machining Debris High Severity
Symptom

Knocking noise, rough engine operation, loss of motive power, or complete engine failure

Root Cause & TSB Details

Manufacturing machining debris left during engine block production causing crankshaft main bearing damage (Toyota Safety Recall 24V-381 / T-SB-0044-24)

Affected Components: Short Block AssemblyCrankshaft Main BearingsConnecting Rods
⭕

Hub Centric Ring Finder & Vibration Eliminator

Precision adapter sizing for Toyota Tundra factory 95.1 mm hub snout.

Factory Hub: 95.1mm
Hub Diagnostic Result
🚨 INCOMPATIBLE WHEEL BORE (TOO SMALL)

The wheel bore (73.1 mm) is smaller than the car hub (95.1 mm). The wheel will NOT physically seat flush on the hub face without wheel spacers or center-bore machining.

💡 Pro Tip: Aluminum billet rings are recommended for track / high brake heat; polycarbonate plastic rings are ideal for salt & winter weather.
📐

OEM vs. Aftermarket Visual Stance & Poke Gauge

Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.

Stock Baseline: 7.5" ET60
New Wheel Width:8.5" (+1.0" vs OEM)
New Wheel Offset (ET):ET50 mm (-10mm vs OEM)
Wheel Spacer (Optional):+0 mm
Stance & Clearance Breakdown🔥 WIDE POKE
Outer Lip (Fender Poke)
+22.7mm
Extends outward toward fender
Inner Lip (Strut Room)
-2.7mm
Closer to suspension strut
FENDER LIPHUB FACE
Inner Strut SideOuter Wheel Face
📋

Printable Mechanic Spec Card & Torque Sequence

High-contrast pocket card for tire shops, track days, and garage toolboxes.

6x139.7
2022-2026 FITMENT SPECIFICATION

2024 Toyota Tundra

fitmentspec.com/toyota/tundra/2024
FINAL TORQUE97 ft-lbs(131 Nm)
Bolt Pattern (PCD)6x139.7
Center Bore95.1 mm
Fastener & ThreadM14x1.5Lug Nut • Conical 60°
TPMS CalibrationDirectDoor Placard PSI
⭐ TORQUE SEQUENCE:Always torque in a star (criss-cross) pattern in 2 stages: 50% initial hand snug, 100% with calibrated torque wrench.
⚠️ NEVER USE IMPACT GUN FOR FINAL TORQUE
🔄

DIRECT HUB-CENTRIC WHEEL INTERCHANGE

Vehicles sharing both the exact 6x139.7 bolt pattern and 95.1 mm hub bore.

✓ No Centering Rings Required
2024-202695.1 mm CB
Lexus GX
Torque: 97 ft-lbsSpecs →
2024-202695.1 mm CB
Lexus GX 550
Torque: 97 ft-lbsSpecs →
2022-202695.1 mm CB
Lexus LX
Torque: 97 ft-lbsSpecs →
2025-202695.1 mm CB
Toyota 4Runner
Torque: 97 ft-lbsSpecs →
2024-202695.1 mm CB
Toyota Land Cruiser
Torque: 97 ft-lbsSpecs →
2024-202695.1 mm CB
Toyota Land Cruiser 250
Torque: 97 ft-lbsSpecs →

⚡ Will It Rub? 2D Offset & Strut Clearance

Real-time inner strut clearance and outer fender poke calculation.

CAUTION: Tight clearance. May contact fender under full suspension travel.
OEM Baseline18x8 ET+50
Rim Width: 8"Offset: +50mm
Target Custom Spec18x8.5 ET+40
Rim Width: 8.5"Offset: +40mm
Inner Strut Shift
-3.7 mm
More inner room
Fender Poke Shift
+16.3 mm
Extends outward
▲ Safe MatchDiameter: +0.10" (+0.31%)
+0.31%
Original Baseline Tire265/70R18
New Target Tire285/70R17
QUICK SIZES:
32.6"32.7"
Speedometer Variance Table
30 mph gauge30.1 actual+0.1 mph
45 mph gauge45.1 actual+0.1 mph
60 mph gauge60.2 actual+0.2 mph
70 mph gauge70.2 actual+0.2 mph
80 mph gauge80.3 actual+0.3 mph
❄️

WINTER WHEEL & MINUS-SIZING ADVISOR

Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.

OPTIMAL WINTER SPEC
255/75R17
Mounted on 17x6.5" Wheel
PCD: 6x139.7
Center Bore: 95.1 mm
🛡️ Technical Benefits for 2024 Toyota Tundra
⛷️ Higher Ground Pressure
A narrower tire (255mm vs 265mm) concentrates vehicle weight onto a tighter contact patch, cutting cleanly through packed snow and slush down to asphalt.
🕳️ Pothole Damage Protection
The taller aspect ratio (+5% sidewall) creates an air buffer that prevents cracked alloy barrels on frost-damaged winter roads.
Brake Caliper Clearance: Verified OEM Rotor FitCompare Side-by-Side ⚡

📡 TPMS Protocol & Relearn Procedure

US OEM Sensor Protocol & Step-by-Step Calibration

DIRECT TPMS315 MHz
Architecture
Direct Valve Stem Transducer
Sensor Part Number
N/A (ABS Sensor)
Relearn Protocol
Cluster-Reset
Relearn Sequence0 / 4 Steps Complete
1
Inflate cold tires to door-jamb pressure
2
Access cluster Settings > Vehicle Settings > TPWS > Tire Pressure Set
3
Press and hold until tire warning light flashes 3 times
4
Drive 10 minutes above 25 mph
TPMS warning light won't turn off after tire rotation?Find OBD2 TPMS Activation Tools on Amazon →

🔍 Pre-Purchase Fitment & Chassis Inspection Checklist

Universal 8-Point Buyer Guide →

✓ Wheel Hub & Bearing Inspection

  • • Note: Gen 3 switched from 5x150 to 6x139.7 with 95.1mm center bore; verify wheel hub centricity.
  • • Torque lug nuts to 97 ft-lbs.

✓ Suspension & Steering Clearance

  • • Inspect new multi-link rear coil spring suspension (replaced leaf springs).
  • • Check front sway bar endlink clearance with aftermarket wheels.
Brake Caliper Clearance Note

18-inch minimum wheel diameter required to clear large front 4-piston calipers.

Common Wear Replacement Parts

📋 One-Click Forum Spec Exporter

Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).

🔩

Verified Hardware & Installation Kit for 2024 Tundra

DIRECT OEM SPEC MATCH
🛡️Owner Crowd Verification(84% Verified)
Verified Fitment & Engineering FAQ

Frequently Asked Questions (2024 Toyota Tundra)

8 Verified Q&As
Q What is the bolt pattern for a 2024 Toyota Tundra?
The factory bolt pattern (PCD) for the 2024 Toyota Tundra is 6x139.7 (6-lug configuration) with a pitch circle diameter of 139.7 mm. Center bore hub diameter is 95.1 mm.
Q What is the wheel lug torque specification for a 2024 Toyota Tundra?
The official factory wheel lug torque specification for the 2024 Toyota Tundra is 97 ft-lbs (131 Nm). Tighten all Lug Nuts in a criss-cross (star) sequence in two progressive stages using a calibrated torque wrench. Re-torque after 50 to 100 miles.
Q What is the towing capacity of a 2024 Toyota Tundra?
The official maximum braked towing capacity for the 2024 Toyota Tundra is 12,000 lbs (5,443 kg) with a maximum tongue weight limit of 1,200 lbs. Recommended hitch receiver: Class IV (2-inch Receiver). Unbraked trailer limit is 1,500 lbs.
Q What is the factory tire size and recommended cold tire pressure (PSI) for a 2024 Toyota Tundra?
Factory stock tire sizing for the 2024 Toyota Tundra is 265/70R18 with a recommended cold tire pressure of 36 PSI front and 36 PSI rear. Always verify exact trim cold inflation pressure on the driver door-jamb FMVSS safety placard.
Q What is the center bore size on a 2024 Toyota Tundra and are hub centric rings needed?
The center bore diameter is exactly 95.1 mm. The hub is hub-centric, meaning wheels center precisely on the axle spigot. If installing aftermarket wheels with a larger center bore (e.g., 73.1mm), precision hub centric centering rings (73.1mm to 95.1mm) are required to eliminate high-speed steering wheel vibrations.
Q What size lug nuts and thread pitch does a 2024 Toyota Tundra use?
The 2024 Toyota Tundra utilizes M14x1.5 Lug Nuts with a Conical 60° seating profile. Never mix conical aftermarket wheels with OEM ball-seat fasteners or vice-versa, as mismatched seating angles cause fastener loosening.
Q Does the 2024 Toyota Tundra have Direct or Indirect TPMS and how is it reset?
It features a Direct TPMS system utilizing physical valve-stem pressure sensors operating at 315 MHz. The relearn protocol is Cluster-Reset: Inflate cold tires to door-jamb pressure
Q What aftermarket wheel offset and tire sizes fit a 2024 Toyota Tundra without rubbing?
For an aggressive yet flush aesthetic without fender rolling or rubbing, the recommended setup is 20x9.0 ET+35 wheels with 295/55R20 tires. For a 100% rub-free conservative upgrade, choose 18x8.5 ET+45 with 275/70R18. Factory safe offset range spans +25mm to +60mm.