2026 Toyota Tundra
Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.
2026 Toyota Tundra Towing Capacity & Hitch Telemetry
Official manufacturer braked tow ratings, max tongue weight, and payload limits.
Up to 12,000 lbs towing with i-FORCE 3.4L Twin-Turbo V6 and factory TOW/HAUL mode; i-FORCE MAX Hybrid rated up to 11,450 lbs.
- • Unbraked trailer maximum limit: 1500 lbs (680 kg).
- • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
- • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.
2026 Toyota Tundra Quick Fitment Answers
Looking for exact hub and wheel specifications for the 2026 Toyota Tundra? The factory bolt pattern is 6x139.7 (6-lug) with a 95.1 mm center bore. The manufacturer specified wheel lug torque is 97 ft-lbs (131 Nm) using M14x1.5 Lug Nuts with a Conical 60° seating surface. Safe wheel offset range is +25mm to +60mm.
Factory OEM Wheel & Tire Configurations (2026)
2 TRIM OPTIONS| Trim Name | Wheel Size | Tire Specification | Placard PSI | Equipment |
|---|---|---|---|---|
| SR / SR5 | 18x7.5 ET+60 | 265/70R18
Compare ⚡
| 36 / 36 PSI | Find Tires → |
| Limited / TRD Off-Road | 20x8 ET+60 | 265/60R20
Compare ⚡
| 36 / 36 PSI | Find Tires → |
🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues
1 DOCUMENTED ISSUESKnocking noise, rough engine operation, loss of motive power, or complete engine failure
Manufacturing machining debris left during engine block production causing crankshaft main bearing damage (Toyota Safety Recall 24V-381 / T-SB-0044-24)
Hub Centric Ring Finder & Vibration Eliminator
Precision adapter sizing for Toyota Tundra factory 95.1 mm hub snout.
The wheel bore (73.1 mm) is smaller than the car hub (95.1 mm). The wheel will NOT physically seat flush on the hub face without wheel spacers or center-bore machining.
OEM vs. Aftermarket Visual Stance & Poke Gauge
Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.
Printable Mechanic Spec Card & Torque Sequence
High-contrast pocket card for tire shops, track days, and garage toolboxes.
2026 Toyota Tundra
fitmentspec.com/toyota/tundra/2026DIRECT HUB-CENTRIC WHEEL INTERCHANGE
Vehicles sharing both the exact 6x139.7 bolt pattern and 95.1 mm hub bore.
Cross-Vehicle OEM Wheel Swap Compatibility (6x139.7)
Verified OEM donor vehicles whose factory wheels fit the Toyota Tundra hub (95.1mm).

Lexus GX
Lexus GX 550
Lexus LX

Toyota 4Runner
Toyota Land Cruiser
Toyota Land Cruiser 250
Toyota Sequoia

Toyota Tacoma
⚡ Will It Rub? 2D Offset & Strut Clearance
Real-time inner strut clearance and outer fender poke calculation.
WINTER WHEEL & MINUS-SIZING ADVISOR
Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.
📡 TPMS Protocol & Relearn Procedure
US OEM Sensor Protocol & Step-by-Step Calibration
🔍 Pre-Purchase Fitment & Chassis Inspection Checklist
Universal 8-Point Buyer Guide →✓ Wheel Hub & Bearing Inspection
- • Note: Gen 3 switched from 5x150 to 6x139.7 with 95.1mm center bore; verify wheel hub centricity.
- • Torque lug nuts to 97 ft-lbs.
✓ Suspension & Steering Clearance
- • Inspect new multi-link rear coil spring suspension (replaced leaf springs).
- • Check front sway bar endlink clearance with aftermarket wheels.
18-inch minimum wheel diameter required to clear large front 4-piston calipers.
📋 One-Click Forum Spec Exporter
Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).