2025 Toyota Tacoma
Wheel fitment, bolt pattern, TPMS calibration, and factory engineering specifications.
2025 Toyota Tacoma Towing Capacity & Hitch Telemetry
Official manufacturer braked tow ratings, max tongue weight, and payload limits.
Rated up to 6,800 lbs with 2.4L i-FORCE Turbo and factory tow package (Class III hitch, engine oil cooler, 7-pin wiring harness).
- • Unbraked trailer maximum limit: 1500 lbs (680 kg).
- • Trailer brakes mandatory for loads exceeding 3,000 lbs in most jurisdictions.
- • Maintain tongue weight between 10%–15% of total gross trailer weight (GTW) to prevent dangerous trailer sway.
2025 Toyota Tacoma Quick Fitment Answers
Looking for exact hub and wheel specifications for the 2025 Toyota Tacoma? The factory bolt pattern is 6x139.7 (6-lug) with a 95.1 mm center bore. The manufacturer specified wheel lug torque is 97 ft-lbs (131 Nm) using M14x1.5 Lug Nuts with a Conical 60° (Aftermarket) / Mag with Flat Washer (OEM) seating surface. Safe wheel offset range is +25mm to +55mm.
Factory OEM Wheel & Tire Configurations (2025)
2 TRIM OPTIONS| Trim Name | Wheel Size | Tire Specification | Placard PSI | Equipment |
|---|---|---|---|---|
| SR / SR5 Standard | 17x7.5 ET+50 | 245/70R17
Compare ⚡
| 32 / 32 PSI | Find Tires → |
| TRD Off-Road / Sport | 17x7.5 ET+45 | 265/70R17
Compare ⚡
| 35 / 35 PSI | Find Tires → |
🔧 Technical Service Bulletins (TSB) & Suspension Chronic Issues
2 DOCUMENTED ISSUESHigh-speed highway steering wheel shimmy between 55-65 mph
Aftermarket wheels installed without hub-centric centering rings (lug-centric vibrations on 95.1mm hub)
Tire rubbing noise on front inner fender liner during full steering lock in reverse
Oversized 33-inch tire setups contacting factory cab mount and front mud flap bracket
Hub Centric Ring Finder & Vibration Eliminator
Precision adapter sizing for Toyota Tacoma factory 95.1 mm hub snout.
The wheel bore (73.1 mm) is smaller than the car hub (95.1 mm). The wheel will NOT physically seat flush on the hub face without wheel spacers or center-bore machining.
OEM vs. Aftermarket Visual Stance & Poke Gauge
Simulate fender lip clearance (Poke) and inner suspension strut clearance in real time.
Printable Mechanic Spec Card & Torque Sequence
High-contrast pocket card for tire shops, track days, and garage toolboxes.
2025 Toyota Tacoma
fitmentspec.com/toyota/tacoma/2025DIRECT HUB-CENTRIC WHEEL INTERCHANGE
Vehicles sharing both the exact 6x139.7 bolt pattern and 95.1 mm hub bore.
Cross-Vehicle OEM Wheel Swap Compatibility (6x139.7)
Verified OEM donor vehicles whose factory wheels fit the Toyota Tacoma hub (95.1mm).

Lexus GX
Lexus GX 550
Lexus LX

Toyota 4Runner
Toyota Land Cruiser
Toyota Land Cruiser 250
Toyota Sequoia

Toyota Tundra
⚡ Will It Rub? 2D Offset & Strut Clearance
Real-time inner strut clearance and outer fender poke calculation.
WINTER WHEEL & MINUS-SIZING ADVISOR
Optimal cold-weather setup for maximum snow bite, pothole cushion, and rim protection.
📡 TPMS Protocol & Relearn Procedure
US OEM Sensor Protocol & Step-by-Step Calibration
🔍 Pre-Purchase Fitment & Chassis Inspection Checklist
Universal 8-Point Buyer Guide →✓ Wheel Hub & Bearing Inspection
- • Jack front wheel off ground, check for play at 12 and 6 o'clock positions.
- • Rotate wheel by hand to listen for growling or gravel-like bearing friction.
✓ Suspension & Steering Clearance
- • Check front upper control arm (UCA) ball joint clearance to inside tire sidewall.
- • Inspect front sway bar end links for torn rubber boots or play.
Factory twin-piston calipers require minimum 17-inch wheel diameter; most 16-inch wheels will contact brake caliper bridge.
📋 One-Click Forum Spec Exporter
Export verified specs for enthusiast forums (vBulletin, XenForo, Reddit).